Anyone with experience with modeling transition metal complexes?

22 November 2018 1 10K Report

Dear all,

May I kindly know if you have any experience with representing metal-ligand complexes on Gaussian?

Best regards

I'm currently constructing a model for a metal-ligand complex using Gaussview 5. None of the default bonding representations; none, single, double, triple intermediate and hydrogen bond are appropriate for representing metal-ligand chelation. Any advise?

Badges
Science topic

More Fidele Ntie-Kang's questions See All

How to make sure each cavity modes with same E-field distribution in COMSOL simulation?

In COMSOL Application Library, there is case about waveguide adapter. But there are some questions: 1) In boundary mode analysis, it just set to find only 1 mode and the S-parameter is...

12 January 2021 9,383 2 View

Where to get per-unit ecosystem services value coefficients for cities?

Per-unit ecosystem services value coefficients are wisely used in ecosystem services research, which is usually in the unit of "money per area for certain ecosystem type/services". The ecosystem...

06 January 2021 4,230 3 View

How to detect protein from dying cells?

Hello, experts. I have been struggling during my Western blot. Briefly, I transfected my gene into two different breast cancer cell lines. The introduction of my gene triggered cell death in one...

03 September 2020 8,799 3 View

What's the difference in antibodies used in ELISA,FACS and IHC?

Hello, I have a question about antibodies used in ELISA, FACS, and IHC. Assuming that an antibody is not labeled or conjugated, what's the difference among them? Can I treat those antibodies in...

27 July 2020 716 11 View

How can I generate Deek's funnel plot in R software, not in STATA?

I am conducting Diagnostic test accuracy meta-analysis. For publication bias, I want to conduct Deek's funnel plot test. I am using R software with mada ant meta packages. However, I found that...

16 May 2020 4,368 1 View

How to grow more BL21 auxothrophic strain cells?

Dear all, I have just purchased a BL21 auxothrophic strain (RF12) from Addgene. The cells come in the form of agar stab. I intend to grow more cells which will be ready to used for protein...

11 May 2020 8,384 3 View

Do you know a lipo battery that is smaller than 10mmX9mmX3mm??

Hi everyone, I'm looking for a small/tiny battery that can generate over 3.2V for biocompatible electronics. Currently, I'm using a 3.7V 12mAh Lipo battery and its size is 10mmX9mmX3mm (WLH). I...

08 March 2020 8,641 2 View

Does anybody know how to draw a pie chart with multiple layers?

I found this graph from literature and it's an excellent way to illustrate similar types of ideas in my opinion. I would like to draw this type of graph in my work but I couldn't find the proper...

14 February 2020 5,933 2 View

How to fit the Gaussian curve based on the moment of power spectrum?

I want to make a spectral correction curve of my light source to resemble the Gaussian spectrum. This literature said, ".. The dashed curve is a Gaussian fit with a center wavelength of 833 nm...

20 January 2020 8,950 2 View

Article of hierarchically structered porous nanofibers by electrospinning?

Hello folks I'm looking for the artice which shows difference of hierarchical structures between membranes and nanofibers. From introduction, I remember it kinda said: hierarchical membranes are...

15 September 2019 470 1 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View