Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

XRPD Quantification - Building a calibration curve of drug excipient?

I am aiming to utilise XRPD to quantify a drug excipient within a drug product and have been having a little trouble building the calibration curve to allow for this quantification up until this...

10 February 2021 6,145 3 View

What could be the cause to have an E.coli DH10B transformed with pUC18 to grow in MKL + ampicillin but is not LAC+?

Hello everyone, I did a transformation of E. coli DH10B using pUC18 plasmid. The bacterias did grow on MKL medium with ampicillin but the colonies showed a white/pink colour and the medium was...

08 February 2021 9,720 3 View

Can I know how to apply contourlet transform for signals in MATLAB?Must I first convert 1D signal to 2D image in order to do this method?

Can I know how to apply contourlet transform for signals in MATLAB?Must I first convert 1D signal to 2D image in order to do this method?

01 February 2021 3,735 3 View

Gain and offset values in Sentinel-2 L1C?

Hello everyone. I have been trying to apply radiometric calibration on Sentinel-2 L1C images (bands 2,3,4 and 8), but every time after layerstacking I come across this error: "Calibration...

28 January 2021 7,160 1 View

What are the pretrained-language-model that is obviously better than BERT and RoBERTa?

19 January 2021 602 2 View

WHOQOL - bref. test: how to conduct the correction?

18 January 2021 7,257 2 View