16 July 2015 1 569 Report

i'm trying to model RC beam in Ansys using Solid 65 elements, solution does not converge when the beam start cracking. how this problem can be solved?

More Laith Zeyd-Kilani's questions See All
What is the best way to encode categorical variables in datasets with many features and avoid increasing dimensionality of the dataset?

I am working with a large dataset that has many categorical variables with many classes in each variable. I want to encode the categorical variables without increasing the dimensionality of the...

31 January 2021 6,986 3 View

If you have the authority to distribute COVID-19 vaccine to which age group or career would you begin with?

Would they be an A: elderly B: women want to be pregnant, C: health care workers, D: immune compromised E: military servants, F: or others? Please specify

14 December 2020 1,108 61 View

How to test an automatically annotated dataset for sentiment analysis?

Dear all, I have annotated a dataset of 7200 tweets with three sentiment classes: positive, negative and neutral. After training and testing multiple classification models with 6000 training +...

17 October 2020 8,501 3 View

Does electromagnetic fields harmful to our bodies?

Does magnetic field can heat the human body? According to the International Commission on Non-Ionizing Radiation protection (ICNIRP), there is a maximum allowable magnetic field exposure to our...

14 October 2020 7,594 3 View

I would like to ask how can i get adiponectin as drug to increase insulin sensitivity in obese people ?

Adiponectin as a drug

23 January 2020 8,571 1 View

Is there a way a can tranfer loads into masses in ANSYS APDL?

i want to make a dynamic analysis in ansys apdl is there a way i can transfer loads (previosly used in static analysis) i have into masses? so i can perform a dynamic analysis.

09 October 2019 6,906 3 View

Why some journals do not have an impact factor?

I have read many topics to understand the impact factor of journal. The confusion is how some journals, for example in Springer, do not have an impact factor? From discussion in this website and...

02 March 2019 8,220 3 View

Is there any articles or papers regarding Agricultural Extension Specialist?

Agricultural extension specialist topics regarding agricultural and veterinary sciences.

31 December 2018 9,622 12 View

What kind of task can be performed with "Twitter News Corpus"?

I have collected above 2.5 millions of news headlines from the newswires in Arabic (BBC, CNN, Aljazeera, AlArabyia, ....etc.) posted on twitter from 2008-now. I am asking about what kind of task...

04 May 2018 9,606 5 View

How to assign polarity for words in sentiment lexicon?

I have read many papers explaining how to assign polarity to each word in the lexicon of positive and negative terms. Some of them such as SentiWordNet assigned 3 polarity scores(Positive,...

02 March 2018 3,977 5 View

Similar questions and discussions
Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close