Contact experts in Simulators to get answers
1,563 views 3,231 posts
Questions related to Simulators
Hi, could I get some suggestions about how to determine (1) the depth of water that infiltrates into the soil profile; (2) whether surface runoff will occur, and if so, how much. Assume that for...
10 December 2021 1,366 3 View
Since TCAD software cannot simulate TFET inverter, I want to use Cadence for simulation. But I can't design A look-up Table based TFET Verilog-a Model. I want to find A look-up Table based TFET...
10 December 2021 7,521 2 View
What are factors which govern the hydrogen storage ability/capacity of Metal Organic Frameworks
10 December 2021 9,779 3 View
I would like to know which is the most influential parameter of the weld bead (especially penetration depth) in laser welding simulation(irrespective of joint type)). How?
10 December 2021 6,978 34 View
Hello Everyone, I am simulating a small wind turbine using Ansys Fluent 19.0. Because of problem periodicity only one third of the fluid domain is simulated. The generated power is calculated...
07 December 2021 8,565 3 View
I am doing grain boundary simulation of multi-crystalline silicon based thin-film solar cells using TCAD Silvaco. On increasing number of grain boundaries in mc-Si region, Voc and FF are changing...
06 December 2021 7,167 8 View
Hi researchers, I've been using HFSS for a while and struggling about getting accurate result in less simulation time. I have one desktop computer to use HFSS and another Laptop to use CST....
02 December 2021 5,828 4 View
I am working in metal forming processes. From literature, it is identified that mostly during simulations of metal forming processes isotropic hardening laws are used, however, the sheet metal has...
02 December 2021 10,008 4 View
Please suggest me their proportion which cause proper curing of FRP.
30 November 2021 6,215 11 View
Good day. The task is to calculate impedance of resonator in case of Gaussian beam circulating. The beam is bunched. Wake potential, frequency spectrum, longitudinal and transvers impedances are...
30 November 2021 2,474 5 View
I am going to simulate a System which requires OPLSAA force field. However, i couldn’t find it out from VMD Library.i was wondering if anyone could help me finding the oplsaa force field and...
27 November 2021 6,173 1 View
I have a multisine signal with BW 5kHz and I bring it into RF domain by multiplying it by an IF signal of 5MHz. The PAPR of IF is greater than that of 5kHz signal. Is there any specific...
23 November 2021 299 2 View
Hi, I need to find an stimation of the Charpy V of my material, but I don't have enought material to do the charpy tests. I have been doing the fracture toughness SE(B) of the material at a...
23 November 2021 8,468 0 View
Heart attack has become the common problem during these day because of our life style and dietary habits which lead to the clogging of the arteries either due to deposition of calcium or...
23 November 2021 8,039 9 View
I am currently working on creating figures for my manuscript - Due to the design of the study I chose to use GLMMs. However, I am now struggling to find some codes on how to illustrate my results....
22 November 2021 6,200 4 View
A fluid fliwing through a tube between two points a and b. we can apply Bernoulli equation . if a hole is created on the wall of the tube between two points a and b, can Bernoulli equation still...
20 November 2021 3,396 13 View
I am new to these network simulators (SUMO and NS3), but need to use the simulators for a project I am currently working on, I want to have three types of communication (V2V, V2R, R2R) the network...
17 November 2021 8,376 3 View
My final goal is to propagare an RF surface wave on a purely reactive surface (Zsurf). First of all I run a mode analysis on a 2D rectangular geometry with a surface current (emw.E/Zsurf) on the...
17 November 2021 7,002 0 View
Just like to accelerate a creep test, Larson Miller Parameter is used, are there any parameters to accelerate a fatigue test?
15 November 2021 5,999 5 View
Instead I get a soil error that says : The initialized C:N ratio of the soil organic matter (humus) in layer 8 is unlikely: 9.0...
15 November 2021 9,783 0 View
Dear All, Please suggest to me which is the best simulator for creating Non-Line of Sight (NLOS) imaging and its processes? Thanks
13 November 2021 7,184 1 View
In SRAM implementation, while performing read operation we need to precharge the bitline and bitline_bar. Do i need to add explicit bit line capacitance for precharging?
13 November 2021 3,436 6 View
Hi, i m trying to simulate a simple vibration cutting analysis, however the choices for boundary condition of velocity for 'rigid' tools doesn't display on the pre processor, its only display when...
09 November 2021 8,875 2 View
Dear all, I'm currently working with halophilic archaea and I am trying to transform them using a spheroplasting protocol and PEG. The original protocols all use 60% PEG600, which unfortunately...
08 November 2021 3,769 1 View