Products made by baking or firing nonmetallic minerals (clay and similar materials). In making dental restorations or parts of restorations the... | Contact experts in Ceramics to get answers
1,810 views 723 posts
Questions related to Ceramics
I would like to know more about this project because currently, I have started my project is also related to this topic. However, I have read a few topics related to this so, I have to know that...
11 May 2017 8,100 5 View
What are the general suggestions regarding dealing with cross loadings in exploratory factor analysis? Do I have to eliminate those items that load above 0.3 with more than 1 factor?
05 May 2017 7,215 30 View
Is it possible to get a measurement model with high reliability and validity while your structural model fit is poor?
05 May 2017 8,653 4 View
these 7 steps are already been covered Explanation of target endogenous variable variance Inner model path Coefficient sizes and significance Outer model loadings and significance Indicator...
05 May 2017 8,734 3 View
Hello . I'm simulating the penetration of an aluminium bullet into a ceramic target in LS-DYNA. the bullet pierces the ceramic, but before getting out on the other side of ceramic, it stops and...
05 May 2017 8,787 4 View
hydroxyapatite with the piezoelectric effect?
05 May 2017 987 2 View
Subject closed
05 May 2017 4,666 8 View
While running AMOS-CV.SEM, Two IVs on DV= Rsquare .14 and its impact on Mediator also Rsquare .14, But Structure Model (including IVs and Mediation impact) the R square value is .72. sample size =...
05 May 2017 9,967 9 View
resistor spark plugs use a 5k ohm ceramic resistor in the spark plug.
05 May 2017 8,301 1 View
The model I am testing using SEM is found adequate in the preliminary test CFA (no reliability and validity issues). However, in SEM of the items are showing factors loadings as low as .291. Can I...
05 May 2017 9,185 6 View
Hi Everyone, Assume that there is a survey instrument which has only independent constructs. In order to check the validity of an instrument, it is mostly suggested to do a CFA in AMOS where we...
05 May 2017 5,459 3 View
After doing various steps in LISREL, i am not able to develop the path diagram. When 'RUN' is clicked, the path diagram diagram is not appearing, instead the same basic model is appearing. What...
05 May 2017 969 2 View
My question is about confirmatory factor analysis. Calculating path coefficients by correlation matrix is hard when we have many variables. How does Lisrel calculate them? Is there any algorithm...
05 May 2017 3,789 6 View
In research papers, authors mention factor loading, t-values, AVE, and CR values to establish validity of scale. But I could not find t-values in AMOS output. How can I calculate t value in AMOS?
05 May 2017 532 10 View
Hello, I am cucrently conducting an exploratory structural equation model with formative constructs in smartpls (what influences a behavior and how does the constructs/items affect this behavior)....
05 May 2017 1,387 3 View
I am doing pilot study, for which I want to do validity test both convergent and divergent, tools want to use are SPSS and AMOS. for validity test in AMOS I draw a diagram (model ) containing...
01 May 2017 2,635 5 View
After successfully running CFA i.e. the model met the criteria of all goodness of fit indices, do we actually check the fit indices in SEM again? If i have successfully run the CFA analysis and I...
04 April 2017 7,748 3 View
Hey there, First I would like to thank for your time in reading my question. Currently I have two data groups with the same analytical model in AMOS, so I would like perform a multiple group...
04 April 2017 9,359 1 View
Hi there, In this post, we want to look at definition of latent variable and how we can calculate latent variable scores. In statistics, latent variables are variables that are not directly...
04 April 2017 5,913 8 View
SPSS, Smart PLS and AMOS are three computer softwares for quantitative data analysis. Please let me know your experience of using the softwares (either one, two or the three softwares, please rate...
04 April 2017 3,693 16 View
I'm testing the unidimensionality of initial model fit.In some constructs covarying the items on the basis of modification indices is providing a better model fit..whereas in some constructs...
04 April 2017 3,340 6 View
I have a couple of concerns regarding the purpose of CFA. Of course, when we are conducting the confirmatory factor analysis we assume that the scales are developed and we have to confirm its...
04 April 2017 7,631 2 View
1) For formative construct's factor weight what is the acceptable range in a structured equation modeling ? 2) Is it possible to keep below 0.7 weight items in our analysis? 3) if I delete 3 items...
04 April 2017 9,713 3 View
what is the proper size distribution for dry pressing of ceramics?
04 April 2017 5,067 2 View