Is there a list of Pubmed indexed all ophthalmology journals?

Whether SCI-expanded or not.

06 September 2020 5,286 3 View

How to solve power system solution for IEEE 30-bus test system given in IEEE CDF?

Hello, I am a Ms. student. I applied the program because I want to learn more about power electronics and renewable energy fields which I have been employed before my undergraduate end. However,...

04 June 2020 5,068 4 View

Is an energy efficient building really better for building occupants?

Assessment of energy efficient design and the occupant well-being

02 December 2018 8,585 3 View

How to model a load with constant voltage in Simulink?

Hello, In my simulink model, i need a model resistive load for DC, which should have constant voltage whatever the input voltage is. I mean for example, the input have 300W power, 30 V voltage ,...

19 July 2018 7,942 7 View

Buffer to disrupt platelet alpha granules for PF4 quantification?

Hello! I want to quantify by ELISA the secreted (from platelets poor plasma) and the non-secreted (from platelet lysate) PF4 before and after TRAP stimulation. I will use the ELISA from R&D...

03 March 2021 1,499 2 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

Dapi fluorescence protocol for colon cell lines ?

28 February 2021 2,534 2 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Can I use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography?

Hi! I would want to know if I can use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography. This column has a polyethylene glycol phase, but I can't find the manual to check...

22 February 2021 730 2 View

How to seperate PEG-4000 from aqueuse phase ?

Hello everyone , Please tell me if It possible to seperat POlyethelyn glycol -4000 from an aqueuse media by other ways rather heating . I have tried salting out by electrolyte solution to...

22 February 2021 7,285 5 View

How to dissolve cross-linked Amberlite IRC120 H, hydrogen form resin?

Hello all, I have used Amberlite IRC120 H, hydrogen form acidic cation-exchange resin for the ion-exchange of waterglass [sodium silicate solution -- 40% Sodium silicate (mol ratio > 3.2)...

21 February 2021 5,614 3 View

Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View