When two-fuid models are applied for gas-fluidized beds , it is observed the numerical stability of the model is so sensitive to the value of the coefficient of normal restitution. why and how can handle it?
Thanks
Vitalii, thank you so much!
You also need to consider the interfacial pressure difference and you need to do a characteristic analysis to make sure the combination is well-posed.
Thank you for your comment, but if we use compressible TFM, we still need to consider the interfacial pressure difference?
It's up to you, but the ill-posed condition is an incompressible problem.
and also convergence of the numerical model? So to prevent these problems, it is better to consider the interfacial pressure difference. Thanks.
Hello, I have done a simulation using CFX in which there are several spheres as fuel and a fluid moves through them and collects heat from them . In order to get some contours of Nu, I wrote...
04 May 2019 7,272 6 View
I have submitted a paper to a journal (Elsevier) 9 months ago. Its status is "under review" for 8 months. I sent several emails to the editor but each time instead of the editor, a clerk answered...
07 August 2017 8,643 5 View
Hi, I am supposed to simulate the flow of Sc-CO2 through a packed bed with spherical fuel. I use fluent 14.5 and its database doesn't support supercritical properties for the flow. the properties...
05 June 2015 4,072 12 View
Hi everyone!I am supposed to use non-equilibrium model in porous zone in Ansys Fluent 14.5. when I interpret UDF on Fluent and start iterating , the iteration is stopped exactly on 40th and I get...
06 July 2014 6,866 7 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
… with my present female lover … she and I spend anywhere from two hours to six hours in caressing, touching, cuddling, hugging, lip kissing, deep kissing and intimate conversation before,...
11 August 2024 4,521 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 718 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 453 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View