Why steel with 1.5 to 4% Mn is brittle, but notably strong and ductile beyond?

11 May 2022 0 6K Report

Dose it have anything to do with Fe-Mn Phase diagram? If yes, how? If not, then what is the mechanism?

Badges
Science topic

More Sumit Bhowmick's questions See All

Help with GFP fusion protein pulldown?

I am trying to pulldown my GFP fused protein of interest using ChromoTek GFP-Trap® Magnetic Agarose. My protein is not binding to the beads. Expression of the GFP-fusion protein has been...

02 June 2024 8,541 0 View

How can I prepare 3 amino benzoyl chloride from 3 amino benzoic acid and thoinyl chloride and which method and what solvent I have to use ?

How can I prepare 3 amino benzoyl chloride from 3 amino benzoic acid and thoinyl chloride and by which method and what solvent I should use ?

15 February 2024 4,834 0 View

How can I prepare 3 amino benzoyl chloride from 3 amino benzoic acid and thoinyl chloride and which method and what solvent I have to use ?

How can I prepare 3 amino benzoyl chloride from 3 amino benzoic acid and thoinyl chloride by which method and what solvent should I use ?

15 February 2024 5,309 0 View

How to quantify the product from 1H NMR?

I'm getting the formate peak around 8.3 ppm. But the main problem is the quantification of the product. If you could give me some instructions on quantifying the product from the proton NMR, that...

07 February 2024 6,858 2 View

I need Global Car sales data (in units) from 1996 to 2021; especially Philippines and Indonesia. Kindly help, if possible send data or share the link?

I need Global Car sales data (in units) from 1996 to 2021; especially Philippines and Indonesia. Kindly help, if possible send data or share the link. Thank You

14 December 2023 174 0 View

What should be the colour (green or bright blue) of the supernatant containing total protein of phototrophic intertidal biofilm?

I lysed my intertidal phototrophic biofilm with hypotonic lysing solution containing 10 Mm Tris, pH 8.0, 1 Mm EDTA, 0.5% Triton-X 100, 1x protease inhibitor cocktail. after complete homogenization...

01 November 2023 5,759 0 View

What is the difference between ambient energy and renewable energy?

What is the difference between ambient energy and renewable energy? Any reference material where I can study these energy sources?

03 September 2023 6,849 7 View

What is the significance of Dead space volume in BET, why and how do we calibrate it and what is the effect of dead space on the experiment?

I'm working on a BET prototype but I'm facing problem in dead space.

28 June 2023 5,609 1 View

How to Stain Poly dT Oligonucleotide?

I have tried with ethidium bromide and stains-all for staining but not getting any band after one day of incubation. I tried with both Native and Non-Native gel.

05 June 2023 377 3 View

Does BET Dosing pressure depend on the adsorbate if both are mesoporous and follow type 4 isotherm?

If we change different type of materials which are in the range of type 4 isotherm and they have similar pore size do we still need to tweak the dosing pressure for both the materials? Even if the...

22 May 2023 9,706 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View