Why sequences appear with small peaks?

More Nadeem Yaqoob's questions See All

What fold change/resistance factor tells about drug resistance?

Results of drug resistance for HCV in http://hcv.geno2pheno.org comes up with fold change/resistance factor. What significance have these fold changes?

09 October 2014 9,884 6 View

I am performing PCR for transiently expressed target genes in tobacco but I am getting the same size very weak bands in WT plants. Any suggestions?

How can I solve this problem?

11 December 2012 7,124 8 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

Is it possible for two human neuronal cell lines to have different gene sequence for the same protein?

I am looking at the ATP1A2 (Sodium/Potassium ATPase alpha subunit 2) in two human neuronal cell lines. Expression levels of this protein seems to be almost equal when detected by one antibody....

01 March 2021 3,607 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Anybody with an idea on how do design specific primers for detecting tomato resistance genes tm-1, TM-2 and Tm2^2?

I am trying to identify these 3 genes among some tomato cultivar collections and after aligning some sequences from NCBI, I couldn't find unique sequences to target for specific primers. There...

28 February 2021 606 3 View

What is the ideal efficiency for a qPCR?

hello everyone, I need to do standard curves for my qPCR, what is the ideal efficiency range? I tried a primer (Mglu2 receptor) that gave an efficiency of 90.2%. Is it accepted?

28 February 2021 1,254 3 View

Michael Marcus Hoffmann

The peak height represent the amount of product produced during the sequencing reaction. If its lower than usual you´ve got lesser products or the injection wasn´t precise. On the other hand, if the peaks are clear it shouldn´t influence the interpretation of the data.

Nadeem Yaqoob

Thanks Michael