20 December 2023 0 3K Report

how to avoid amine when our target product is imine

is my catalyst not suitable ?

how to decide that me catalyst could not give 100% selectivity? or is not good enough for this reaction?

More Rabia Abbas's questions See All
In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Similar questions and discussions
How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View

Ligands with 3,4,5-trihydroxyphenyl group?

Hi In the design of a bidentate ligand with imine group, is it okay to have a 3,4,5-trihydroxyphenyl group in the structure? In other words, does the 3,4,5-trihydroxyphenyl group compete with...

08 February 2021 4,977 7 View

Is there any books or journal that specifically discussed TPR in detail?

I am designing a metal oxide catalyst and among many characterization of this sample, TPR emerges quite significantly. The brief explanation in journal is limited to the sample that is...

21 January 2021 6,346 1 View

How cane capture of Cl, K , Na, in the process of biomass gasification, I want to let these elements enter the solid slag phase but not enter the gas?

I want to fixation Cl, K, Na in gasification slag, which type of catalyst can be used?

13 January 2021 2,145 2 View

How can I produce Alpha-monopropionin and Alpha-monobutyrin in lab scale?

I understand that glycerol should be reacted with propaoiocic acid to produce monopropionin and with butyric acid to produce monobutyrin , if you can help with the reaction conditions based on 1...

13 January 2021 1,151 4 View

How to calculate the concentration for as prepared nanomaterials?

if we are taking 2 materials of different concentrations (one is the precursor and the other one is the stabilizing agent) for synthesizing nanoparticles as a catalyst, how can I calculate the...

08 January 2021 516 4 View

What does this PZC data mean?

I measured different kinds of catalysts which were dispersed in DI water.I firstly added certain amount of HCl and then used NaOH to titrate and measure the pH value. What does this result mean?

27 December 2020 5,728 4 View

How can we choose the right method for Gaussian calculations?

I'm not working on biomolecules, I work on Organic, Organometallic, and sometimes inorganic structures. Do you know a simple way to apply the right calculation method? Is there any article or...

10 December 2020 3,396 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close