Why does not ABAQUS show pinching effect in cyclic loading?

More Hamed Dabiri's questions See All

How many verification is needed for a FEM structural element like RC joint?

there is no room for doubt that a numerical structural element (like beam, column or joint) should be verified by a similar experimental study. the question is that how many models should be...

08 September 2018 9,193 5 View

Is it possible to publish two different papers with the same "introduction" and "methodology"?

Researchers who work on a topic, sometimes publish more than one paper because of the huge amount of the study outcomes. my question is that is there any problem if the "introduction" or...

07 August 2018 5,221 32 View

Which factors should be considered for reviewing a research article?

It is clear that disparate sections of an article should be assessed to check whether it meets the minimum requirements of a journal or not, but my question is that how we can review a research...

07 August 2018 7,556 3 View

What does the status "Review Completed" means?

I sent a manuscript to a journal about one month ago and it's one week now that the status has changed to "reviews completed". I want to know why the status has not changed for one week and what...

05 June 2018 2,986 5 View

Is publishing a paper in an ISI journal without impact factor (IF) recommended? why or why not?

there are different ISI journals which do not have an impact factor. what's your opinion about publishing a paper in one of them?

05 June 2018 2,416 11 View

What are the upwards of publishing a book based on the university thesis?

Some researchers believe that publishing a book using MSc or PhD thesis could be a positive point on academic CV while others don't. I would be appreciated if you can leave your valuable comments...

05 June 2018 7,953 6 View

How the yield displacement of concrete elements is calculated?

yield displacement of an element is defined as the displacement when the concrete strain reaches to 0.0035 . I'm looking for a valid reference (paper or book) related to this matter.your help is...

05 June 2018 3,502 8 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

Frank Richter

Hello

subscribe to and seek assistance from the

ABAQUS mailing list

https://groups.yahoo.com/neo/groups/Abaqus/info

Search the archive of the list before posting in it.

The list does not accept attachments.

http://www.eng-tips.com/threadminder.cfm?pid=799

For advice on mechanics in general, including modeling,

you can consult

http://imechanica.org/

Good luck

Frank

Dušan Regodić

1. https://groups.yahoo.com/neo/groups/Abaqus/info

2. https://groups.yahoo.com/neo/groups/Abaqus/info