26 January 2022 3 8K Report

We produce ferrosilicon used by submerge method. In this method we use silicon, carbon and iron oxide.

W have a problem. 18 hours after end of produce, ferrosilicon become powder. Why? How can I prevent this problem?

Thank you

More Ehsan Allahyari's questions See All
In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Similar questions and discussions
What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Can water be extracted from Olivine?

I have always been interested in geology and wondered about how unique structures of materials behave in different circumstances. I stumbled upon Olivine, the magnesium iron silicate, and heard...

28 February 2021 7,330 4 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close