Why do numerical scheme for Phase field modelling (Cahn Hilliard Equation) need to satisfy energy constraints?

More Deewakar Sharma's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

If my gene of interest has high GC content can it be problematic in sequencing? What kind of error is expected with GC rich gene sequences??

Gene sequencing related trouble shooting

25 July 2024 4,149 2 View

How to dispose off lipids waste?

I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...

25 July 2024 637 5 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

How effective has the United Nations been in addressing the conflict and its consequences?

After World War, we have seen the formation of the United Nations. The sovereign body for peacekeeping but with regards to the Russia-Ukraine war it is visible that the UN seems to be ineffective...

18 July 2024 4,674 4 View

What are the main obstacles to achieving a ceasefire or peace agreement between Russia and Ukraine?

It has been a quite long time since the Russia and Ukraine war has been going on and if we see the context of Geopolitics and International Relations we don't see a mediation between the two...

18 July 2024 6,737 4 View

How to decide whether the refinement is correct or not, based on Rwp and Rexp factors by Fullprof?

One of the papers I read by Toby, where (title of the paper was "R factors in Rietveld analysis: How good is good enough?"), he tells us that to get good chi square value, you must have low Rwp,...

17 July 2024 9,668 4 View

How to draw photon-magnon coupling color plot in origin?

Please help me in plotting the photon-magnon coupling plot as shown below

14 July 2024 1,632 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Zoubair Boulahia

Look at this doc it may be helpful for your topic. Good luck.

Deewakar Sharma

@Zoubair

The attachment is titled 'PERFORMANCE ANALYSIS OF GRID-CONNECTED WIND TURBINES'. No where I could see anything related to phase field modeling.

Thanks

@Deewakar I change it by the exact doc that I want upload. Good luck.