04 April 2019 1 3K Report

Hi all

I'm simulating a rotating part by scoping it's end faces using joints. But applying displacement or rotation I don't see any stress. What is the general root cause of it?

More Farzad Torabi's questions See All
Why do I get error in post processing after each loadstep in ADPL ?

Hi all I need to postprocess a multi step analysis in APDL. but I am not sure how to write it. I Use LSWRITE,1 TIME,1 NSUBST,100,200,100 for the step one, then I define the load and then use...

01 February 2020 3,355 4 View

How do I point to my created material in Ansys eng configs using APDL ?

Hi All How do I point to the material I have created in Engieering configs of Ansys ( I also use workbench) How do I point to this created material in APDL code ?

31 December 2019 4,414 3 View

When can we pass from a 50% confidence wohler curve to a 95% confidence interval curve?

Hi All when can we pass from a 50% confidence curve to a 95% or 97.5% curve while constructing and testing for Wohler Curve ?

10 November 2019 2,364 4 View

How to define frequency dependent damping in Ansys Harmonic?

Hi All How can I define frequency dependent damping in Ansys ? it seems to be Damping frequency, but I am told that the value I input here, is used only to calculate the stiffness matrix...

10 November 2019 8,175 5 View

Why does FeSafe give a higher stress for the worst cycle than the max stress of input FEM?

Hi All When I input a FEM model to FeSafe while I know its maximum von mises stress, even when I apply a sinusoidal loading , I see a higher stress in largest stress of worst cycle than that von...

09 October 2019 3,633 4 View

How can I solve a modal analysis with spherical coordinate systems in WB ANSYS?

Hi All is there a way to define a spherical Coordinate system in WB Ansys using APDL snippets and solve the problem accordingly ?

07 August 2019 5,200 0 View

How do deal with Abaqus bolts from flexible to rigid ?

Hi All I have a bolted structure, Solid , in Abaqus in NL static analysis. there is a stress concentration on the bolts when the bolts are flexible. but when I turn the bolts to rigid, the...

07 August 2019 2,481 2 View

How can I sketch a curve in Abaqus API having its function?

Hi All I need to sketch a curve in abaqus api having its function. how to do that ?

07 August 2019 6,045 2 View

How do I use probability in the stress level of Wohler Curve?

Hi all in an HCF analysis for a Shell body, how do I use probability in Stress level in wohler curve ?

05 June 2019 4,126 8 View

How to construct the optimization for a batch run in FEM?

Hi All I have the stress output of a structural analysis plotted against x ( x range is constant in all cases) that is a curve with minimums and maximums. changing the model chracteristics (...

03 April 2019 5,194 7 View

Similar questions and discussions
How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close