Why am I obtaining the exact same results during cool analysis of different channel pitches and geometries in Solidworks Plastics?

More Laura Simiyu's questions See All

Consequences of excess bases in the MCS after digestion?

Good morning, I am trying to produce a recombinant protein. Unfortunately I one of the two restriction enzymes that I use do not cut at the end of the MCS. After the digestion 15 nucleotides of...

17 July 2024 2,787 4 View

Is perfusion required to stain brain tissue with every method?

I'm looking to immunostain some brain tissue collected previously. The animal was *not* perfused prior to tissue collection. Will the presence of blood interfere with all staining methods...

14 July 2024 177 4 View

Is there a validated questionnaire for target audience research?

Hi everyone, I am currently writing my masters thesis about Strategic Sponsor Acquisition in Youth Women's Soccer. The aim of the study is to identify potential sponsors for a specific youth...

04 July 2024 9,001 0 View

Posting a research survey ?

Hi i want to post this in various groups, how do i do that ? hey, please do my survey when you get the chance, it will take 15 minutes tops x I am looking for UK secondary school teachers to...

30 June 2024 9,594 2 View

Can I use richer media to increase bacterial expression of human protein?

We're using LB media, 1mM IPTG, and letting it incubate at 18°C over night. Will adding glucose or something else to the media increase bacterial expression?

06 June 2024 6,071 1 View

How to scale up or down a restriction enzyme reaction?

Hi I am trying to set up the reactions with my plasmid, insert and RE. Usually the standard final volume is 20 uL or 50 uL (it depends on the protocol provided by the manufacturer) with 1 ug of...

28 May 2024 1,105 3 View

Algae contamination on hydroponic cultures for Arabidopsis thaliana?

Hi everyone, I'm having trouble with my hydroponic cultures for Arabidopsis thaliana, since lately I've started having algae contamination on them. I have tried using several sterilization...

21 May 2024 4,840 1 View

How to set up a restriction enzyme reaction?

I'm a doctoral student with early experiences with recombinant protein synthesis. Since I still have to start my experiment and I do not yet know the quantities of DNA and plasmid that I will...

19 May 2024 5,171 3 View

What is recommended as a strong and current reference of phenomenological analysis ?

What is recommended as a strong and current reference of qualitative phenomenological analysis ?

16 May 2024 2,142 1 View

Is there any guide to perform statistical analysis of transcriptomics?

I am looking for a some chapter or book related to the statistical analysis of mRNA transcriptomics. Thank you;)

09 May 2024 6,543 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

What is the difference between alluvial and fluvial?

I have made an unpleasant discovery that I seemed to use these terms incorrectly. 'Alluvial' seems to mean "out of the river channel", flood-plain' etc. While all these cross-bedded...

15 July 2024 2,073 3 View

How to add channel doping variation in sentaurus tcad to see its effect on transfer characteristics of mosfet?

I am getting trouble in studying the effect of channel doping variation in forksheet structure for p and nmos.

08 July 2024 2,074 0 View

• How can scientists ensure their research findings are effectively communicated to the broader public?

Effective public communication of research findings requires a combination of skills, including translating technical information, crafting engaging narratives, leveraging multimedia, and actively...

01 July 2024 1,330 2 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

A new interesting geometry problem. Can you find the measure of angle?

In the isosceles triangle ABC (AC=AB), the angle at the vertex is 20°. Point D is chosen on the side AB such that AD=BC. Find the measure of angle CDB.

23 June 2024 7,541 8 View

Алексей Ялышев

does the filling time change?

how does your graph look like?

Debrayan Bravo Hidalgo

Dear, Laura Simiyu

I think you should change the filling type and try.

Laura Simiyu

Алексей Ялышев, Debrayan Bravo Hidalgo i realized when it changes the answer is no longer the same. Thank you.

In your opinion, the hat else would help vary the results?

Then when seeking to obtain cooling time, is this GE time given under COOL or that under FLOW? They differ considerably. Thank you.