see above
Department of Chemical Engineering, Indian Institute of Technology Kanpur is focusing on polymeric coating and patterning on variety of substrates.
department of physics, faculty of science, University of Malaya
http://fs.um.edu.my/
here is a big group of staff and student focusing on polymeric coating
Hi We are looking for polymer by UV resistant as low as possible. I appreciate if some one can suggest us. Sincerely yours, Mohammad
02 March 2017 5,291 8 View
Does biocide need to release from material for killing bacteria or if they grafted to polymer they would have antibacterial effect? Regard,
07 August 2016 5,867 2 View
For example study the number of bacteria by CFU, and using of this result for antibiofouling properties ? Thanks
06 July 2016 8,974 1 View
Can anybody suggest some resin for used as matrix of superhydrophobic coating? I know some resin like. PDMS and fluoropolymer resin, but I would like to know some resin for this application that...
06 July 2016 5,064 8 View
Is epoxy resin a good candidate for use as a matrix of superhydrophobic coating?why? Thanks
06 July 2016 9,339 4 View
Hi Microorganism would like to attack in which type of molecular bonding?(especially which type of atoms?)
05 June 2016 4,143 3 View
I am looking for a paint (or solution) that has a water base properties plus a few surface energy. And additionally available in market. I find perfluoromethyle acrylate co-polymer (PMCs) but they...
03 April 2016 7,630 1 View
I‘m working on surface modifications of polymeric coatings for anti-biofueling coatings. Would this software help with this project?
03 April 2014 2,279 1 View
I am trying to model a surface by using software
03 April 2014 7,501 20 View
For polymeric coating.
03 April 2014 6,394 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
Your comments
28 July 2024 2,822 2 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View
Novel areas especially
24 July 2024 8,416 0 View
I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...
23 July 2024 4,074 2 View
I have immunized BalB/C mice with a protein using the intradermal (ID) method with Complete Freund's Adjuvant (CFA) and Incomplete Freund's Adjuvant (IFA), following a 14-day interval and three...
22 July 2024 9,160 2 View
Dear Participants- Faculty and Researchers from Pakistani Higher Education Institutions, Thank you for participating in research study that aims to 'Analyze Individual and Institutional Factors...
18 July 2024 7,024 1 View