Which method/ open-source software is the best for Microstructure modeling? Any relevant resources regarding microstructure modeling?

More Somnath Somadder's questions See All

Is it correct to treat RAW264.7 mice macrophage cell line with recombinant Human Macrophage Migration Inhibitory Factor (MIF)?

Is it correct to treat RAW264.7 mice macrophage cell line with recombinant Human Macrophage Migration Inhibitory Factor (MIF). Will there be any species incompatibility related unwanted effect on...

12 November 2023 1,533 1 View

CMV and EF-1alpha promoter in same plasmid?

Hi I was wondering whether CMV and EF-1alpha promoters can be put in a single plasmid? Are there any compatibility issues between the two promoters? Thank you.

31 October 2023 9,919 2 View

ED50 of Meropenem in Mice against Klebsiella?

I am looking for the ED50 of meropenem in mice against Klebsiella systemic/lung infection models. Is anybody aware of it? Thank you.

18 June 2023 2,017 0 View

Which softwares are better to draw schematic diagrams of beams, plates etc?

I want to know which software is used by authors to draw schematic diagrams of beams, plates etc. for there articles.

22 May 2023 7,631 6 View

Is there a publication that discusses expression of different glycosylation enzymes in different CHO cell lines?

Hi I am kind of looking to see if a comparative expression level analysis of the different Glycosylation enzymes of different CHO cell lines (DG44, DXB-11 and K1)is available in any publication. I...

12 April 2023 9,491 2 View

DTM is the only method to solve elastic support beam vibration problem??

Most of the available literature related to vibration of nanobeam with elastic support boundary condition, author use Differential Transform Method (DTM) to solve the governing differential...

19 March 2023 3,763 2 View

Site directed mutagenesis not working. Can anyone help?

I am trying to replace a 20 bp region with a different sequence of same lengthin a 10kb plasmid. I designed overlapping primers. However after PCR I am only getting the template. At first I...

13 February 2023 3,662 3 View

Why does relative energy of conformers change when dispersion corrections are included during DFT calculations?

During conformational analysis of 18crown6, it was observed that the conformer with S6 symmetry was having the lowest energy when dispersion correction was not included. However, upon addition of...

14 February 2022 1,492 3 View

THP-1 requires differentiation before Phagocytosis assay?

I am looking to study opsonophagocytosis using THP-1 cell line from ATCC. Does the cell line require differentiation before the phagocytosis assay?

28 October 2021 3,411 5 View

Could you suggest me how to study the interaction of fungus/bacterial pathogens or bioagents with host based on fluorescence lifetime microscopy ?

Kindly share your publication on this aspect Regards Somnath Holkar

07 October 2021 6,646 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,114 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,003 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,891 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,047 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 717 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,984 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 452 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,664 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,027 4 View

Safkat Islam

Sir,

For Microstructure Modeling you could try NEPER. Also, open-source software MOOSE Framework by IDAHO National Laboratory. For Crystal Plasticity, ABAQUS or DAMASK.

This link may help you: https://www.youtube.com/watch?v=tz7lmqiYdCw

Prokash Chandra Roy

Sir, we are actively using NEPER for phase-field simulation.