Control in microstructure with growth inhibitor?

Dear researchers, I wish to understand the role of grain growth inhibitor in controlling the microstructure of the ceramic pellet. How it controls the growth? Also, I wish to know the grain...

15 January 2021 3,859 3 View

No title

11 January 2021 3,284 3 View

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,594 2 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

What are the invivo screening methods for anti TB drug?

what are the invivo screening methods for anti TB drug?

25 December 2020 722 1 View

Which are the vendors who sell commercial SWIR (NIR-II) dyes?

I am searching to find commercial vendors who sell SWIR dyes. I could only find Nirmidas Biotech which sells different NIR-II dyes!

23 December 2020 5,002 3 View

How to get doi of presentation ?

doi of your presentation in the conference

23 December 2020 9,370 2 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View