10 October 2017 0 8K Report

Openfoam or Starccm or Ansys-CFX

More Manigandan Sekar's questions See All
In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

10 November 2019 3,972 3 View

How to draft a review paper effectively in short span of time for high impact journals?

Writing a review paper required a lot of effort. Any tactics is there to complete it in short span of time. Especially for Elsevier or reputed journals with high Impact factor.

06 July 2019 2,293 3 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

05 June 2019 268 4 View

No title

I came across few having 3 PhD in different fields. Am very confused about this ? Thanks in advance

02 March 2019 7,556 2 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

01 February 2019 1,137 15 View

Differences between research papers and technical note of journal?

Can i write an technical note below 1000 words. If not what is the idle limit for them. Is there any mandatory rules

31 December 2018 9,217 1 View

Best way to access recent Engineering Books in online ?

I need to access the book : Energy Efficiency in Air Transportation Published by elsevier. I tried many options but no use. Since i can't afford to buy this, is there any way to access the ebooks

31 December 2018 4,163 4 View

How to solve Blast in FEA ?

What are the boundary conditions are required for blast loading. Share the tutorials if possible.

31 December 2018 1,249 0 View

What is the difference between review track and non review track in Elsevier conference ?

In Elsevier conference there are two options for paper submission Review track and non review track. What is the meaning for that. Will they publish both articles in supporting journal

07 August 2018 3,866 0 View

How to approach Faculty Exchange Program to the foreign Universities ?

Hi Am looking for an Faculty exchange programme vacancy in foreign universities to improve my career in technical fashion. I don't know how to start them. Can anyone guide me

07 August 2018 8,713 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close