How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

Amorphous silica XRD peak at around 10 degree?

21 February 2021 3,417 5 View

What is the detection limit of ED-XRF technique for transition metals in silicon ?

Hi everybody, please, can someone tell us if the transition metals (W, Fe, Ni, etc ...) in silicon destined for solar cell manufacturing can be detected by ED-XRF technique. Note that the...

18 February 2021 6,231 4 View

Unusually Busy Raman Background?

Hello, I am observing a nearly periodic background spectrum for a wide variety of SERS substrates. I see this response (attached below) for bare Au films, Cu films, and Au nanoparticles on...

15 February 2021 9,922 5 View

Sound transmission loss (Acoustic Metamaterial)?

My design contains three parts. A silicon rubber membrane is placed between upper and lower part. I want to calculate sound transmission loss by using comsol Multiphysic. There are lots of...

05 February 2021 466 4 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View

How can you make a PEDOT:PSS film using the doctor blade technique?

I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...

01 February 2021 8,506 5 View

What is the most efficient way to generate amorphous silica in LAMMPS?

I would like to generate multiple large samples of amorphous silica in LAMMPS. Currently I am generating it by beginning with a lattice of silicon and oxygen atoms and using a melting and...

28 January 2021 6,128 4 View

How do you obtain an even spread of polymer film on Silicon wafer?

Hi Everyone, I made some polymer(Polylactide) films on Silicon wafer. The polymer was dissolved in DCM and THF. I observed that the colour of the film at the centre of the Wafer is different...

27 January 2021 9,724 1 View