27 December 2016 4 8K Report

Am in need of LM25 alloy in as cast condition in the form of ROD shaped of diameter between 10 mm to 15 mm and a length of 500 cm.

Any information you can provide me would be greatly appreciated.

More Dhanashekar Manickam's questions See All
What are the effective ways to remove microorganisms in plants and their roots without killing or damaging the plant?

I intend to utilize a 2-inch plant, since it takes about a year for a plant to grow from the root. So, I must remove the native microorganisms (that is already present in the plants and their...

28 April 2024 3,055 2 View

Have anyone faced the problem of Modified Krebs–Henseleit solution having raised pH after bubbling with carbogen?

Hi all, I have used the standard MKHS composition to make this buffer. The initial pH of the solution was 7.7. I adjusted the pH to 7.3 with 1N HCL and bubbled with carbogen (95% O2 and 5% CO2)...

13 September 2023 3,052 3 View

Questions related to stresses on thick cylindrical pressure vessel?

In a thick cylindrical pressure vessel, what are all the types of stresses acting on them? and tell that magnitude of various stresses acting on thick cylindrical pressure vessel in decreasing...

08 January 2021 7,550 0 View

Nuclei isolation from Pancreas? All the nuclei that I have isolated look good but they are all clumped together in gelatinous matrix? Any inputs?

Nuclei isolation from Pancreas? All the nuclei that I have isolated look good but they are all clumped together in some sort of gelatinous matrix? Does anybody have any inputs to improve the...

03 April 2020 8,187 2 View

What are the high yielding methods of extraction of phycocyanin from dry mass of Anthirospira plantesis?

extraction techniques

31 January 2020 7,426 1 View

What contributes to Trichoderma pellet stability in production media?

Hello all, I am currently working on pellet induction in Trichoderma sps. for the production of cellulases. Although I am able to induce pellets of somewhat uniform size and compactness in a...

08 April 2019 9,589 0 View

How good the antibodies from Sabbiotech, USA?

Hello, Had anyone used antibodies from Signalway, Sabbiotech, USA for western blotting?. If so, kindly gives your comments about the quality of primary antibodies.

29 July 2018 2,191 1 View

How to find the actual coordinate form the normailzed image value?

Hi, For example, I have a 500*500 size of image, but I normalized the range of [0 1], then how to find the image actual coordinate value from the normalized image value

08 February 2018 2,525 4 View

How to extract natural dye whish is the best method for dye extraction?

i need some clarifications for dye extraction method. i am working in TiO2 dye sensitized solar cells.

09 January 2018 7,550 3 View

Can any one suggest the reference book for Data Analytics?

Dear Researcher (s) Can any one suggest the reference book for Data Analytics?

11 December 2017 6,308 2 View

Similar questions and discussions
Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Concentration of gelatin as brain model ?

I am using gelatin to model mechanical properties of brain tissues in-vitro. Do you have any suggested concentration ? Thank you so much.

19 July 2024 3,095 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close