Where can I find a microfabrication lab in Germany?

More Abdulkarem Odhah's questions See All

Dose the thinner affected on the concrete when added it?

i want to uses it in concrete

27 December 2018 3,158 2 View

What is the difference between Distributed based RAN (D-RAN) and Fog based RAN (F-RAN)?

In cloud-based RAN (C-RAN), all the signal processing were transferred from the local or small cell base stations (i.e. Distributed D-RAN) to a centralized center to simplify the network...

05 February 2018 2,941 3 View

Droplet PCR in plastic chips always result an unexpected band, any suggestion of possible contaminations and how to improve?

I am doing droplet based digital PCR inside plastic chips. I can get the correct band, but I also consistently get an unexpected band, slightly shorter. I attached a typical gel image here....

18 February 2021 6,618 2 View

How to remove colour from DNA pellet during DNA extraction?

I am working with Amaranth accessions which are green to red in color and contain high phenolic compounds. Using the CTAB method with the slight modification I am trying to get high-quality DNA so...

18 January 2021 3,578 1 View

A three electrode sensor inkjet printed gets damaged in few hours of usage in a dynamic media flow chip, any solution for that?

We are using some biosensors which are inkjet printed and are used in the microfluidic chip where media is flowing at the flow rate of around 60 uL/min. However, after the continuous use of few...

05 January 2021 610 2 View

Is any way or method to seal agarose pad or channels fabricated agarose gel pad to glass slides as like we do plasma bonding with PDMS to slides?

Is any way or method to seal agarose pad or channels fabricated agarose gel pad to glass slides as like we do plasma bonding with PDMS to glass slides?.

04 January 2021 3,589 2 View

How to clean LEDs (InGaN on SiC) and Ti/Au electrode chips?

I need perfect cleanliness for further processes but I am not sure which cleaning method would be sufficient yet letting the layers intact.

01 December 2020 1,099 2 View

The algal cell always gather together when the cells concentration is high and those cells would block the microfluidic chips. How can i handle it?

I want to pump a high concentration algal cells into microfluidic chip, however those cells are always gather together forming a clusters to block the connection between Teflon tube and...

26 October 2020 5,366 2 View

Can any one tell me that how we represent RFID chip (Z=23-j224) with a discrete port in CST?

Dear All, I am facing trouble in making antenna for RFID tag. Just tell me that how a chip resistance represents by discrite port in CST? for example I am using NXP chip with...

22 October 2020 7,968 2 View

Have spin-based devices found any appilcation in medical science?

Spin-based devices such as magnonic chips, spin-torque oscillators mostly find their application in signal processing, computing, etc. Is there any research work focusing on developing magnonic...

17 October 2020 3,459 1 View

What can I do with Bioanalyser Ladder Problems?

I'm using the Bioanalyzer DNA 1000 to check my amplicons 16S. But when I run the chip, I can't see the pb scale. Just appeared in x axial the time (s). In the last run the message "not all...

29 September 2020 8,021 4 View

How can I simulate a droplet motion on a digital microfluidic chip using COMSOL Multiphysics??

Hi, I'm trying to simulate a DMF (digital microfluidic) chip in COMSOL Multiphysics 5.5. I used a 2D model and selected two phase flow, level set and electrostatic modules to simulate a droplet on...

26 September 2020 1,392 6 View

Ana Fernández-la-Villa

We can help you with martes molds for PDMS microfluidic fabrication from Spain (www.micruxfluidic.com)

In Germany you can contact Microfluidic ChipShop (https://www.microfluidic-chipshop.com/services/)

Dominick I. Ndjandjo Ntamag

Hi Abdulkarem, The lab I belong to makes microfluidic chips, but it depends on the company's projects. Off the top of my head, i can recommend Bartels mikrotechnik and Microfluidic chipshop. Unfortunately, I have no idea about shipping and costs.

https://www.bartels-mikrotechnik.de/en/microengineering-english/

https://www.microfluidic-chipshop.com/

Abdulkarem Odhah

Dear Ana Fernández-la-Villa and Dominick I. Ndjandjo Ntamag ,

Many thanks for your answers.

Would you please let me know if those providers (MicruX, Microfluidic ChipShop, and Bartels Mikrotechnik) offer the microfabrication service for a single piece based because I think they only accept large quantities purchase.

Hi Abdulkarem. We will not provide you the final microfluidic. What we can offer you is a master mold, and then you can fabricate as many chips as you will need using PDMS material. I do not know if PDMS will be compatible with your experiments, but if this is an option I will be happy to assiti you with further details.

Hi Abdulkarem Odhah I don't think that Bartels does and for Microfluidic shop (I don't know) you can write a request and they'll tell you.