Where can I download JMatPro software for thermodynamic modelling ?

More Mohammad Shahrear Kabir's questions See All

What software would be best to simulate impact environment ?

I am trying to investigate the impact nature of steel balls (4 cm diameter) on steel plates. Which modelling software would be best to study the stress fields generated or any type of failure...

11 December 2019 1,943 4 View

What is the optimum austenization hold/soak time for cast structures?

I am looking for studies related to austenization soaking times and ways to reduce the time to achieve full dissolution of carbides as well as not to obtain austenite grain growth. Grain growth...

10 November 2019 4,824 3 View

Are there any studies regarding fully pearlitic/eutectoid steels with relation to soaking time during austenization ?

I am working on developing fully pearlitic steels with fine interlamellar spacing. I am going to heat up samples to austenization temperature (1000 degC) at a heating rate of 10 degC per second...

09 October 2019 5,325 3 View

Are there any relevant work on impact-abrasion wear testing?

I am working on a project involving studying the impact-abrasive wear during grinding. I am interested to know if there are any relevant papers that has studied or tested impact-abrasive wear of...

08 September 2019 6,970 2 View

Can MATLAB be used to simulate nano or micoindentation by Berkovich or Vickers?

Can 2 dimensional simulation of indentation be done using MATLAB? if yes, I would really appreciate guidance from experienced MATLAB users !! Thank you

10 November 2018 2,043 2 View

What can be the reason for reduction in hardness and toughness of thin films or coatings due to doping with silver (Ag) ?

I have deposited pure Cr and W films by unbalanced magnetron sputtering method and then prepared films by doping them with Ag. The hardness and modulus of these coatings are lower than that of the...

01 February 2018 5,046 10 View

Does the presence of excess lattice oxygen in thin films or coatings signify high surface energy of the films or coatings?

In cerium oxide coatings, I have found that there are excess lattice oxygen when oxygen to metal ratio is quite high. Does it mean that the coatings have higher surface energy when there is excess...

31 December 2017 4,995 3 View

Where can you purchase synthetic/artificial synovial fluid or anything that closely resembles synovial fluid?

I am designing experiments to study the tribological behaviour of coated Ti6Al4V in synovial fluid. Any help would be highly appreciated.

10 November 2017 2,496 2 View

Can anyone kindly suggest me where to start learning simulation/modelling of Nanoindentation?

I would like to learn FEA method for nanoindentation for materials. I would really glad if someone would suggest as to where I should start learning simulation/modelling.

05 June 2017 6,901 4 View

How to calculate the adhesion energy of coatings from progressive load scratch testing?

Is there any procedure for calculating the adhesion energy of coatings by progressive load scratch testing. The samples are CrAlN coatings on tool steels.

02 March 2017 5,436 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Seyedmohammad Tabaie

You can find it in torrent, but most of them are version.7 or lower.

Anand Dabadgaonkar

suggest site to download those software......

Deepu Mathew John

Hi. JMatPro is a commercial software. You need to buy it if you want to use it for thermodynamic calculations. However, the company offers a demo version, which can be accessed in the link below:

https://www.sentesoftware.co.uk/demo

Demo version is free to use, but you can't perform any new calculations. You can access some demo calculations that are already shared with the demo software. With this limited capability, you should be able to evaluate the software.