Where can you purchase synthetic/artificial synovial fluid or anything that closely resembles synovial fluid?

More Mohammad Shahrear Kabir's questions See All

What software would be best to simulate impact environment ?

I am trying to investigate the impact nature of steel balls (4 cm diameter) on steel plates. Which modelling software would be best to study the stress fields generated or any type of failure...

11 December 2019 1,943 4 View

What is the optimum austenization hold/soak time for cast structures?

I am looking for studies related to austenization soaking times and ways to reduce the time to achieve full dissolution of carbides as well as not to obtain austenite grain growth. Grain growth...

10 November 2019 4,824 3 View

Are there any studies regarding fully pearlitic/eutectoid steels with relation to soaking time during austenization ?

I am working on developing fully pearlitic steels with fine interlamellar spacing. I am going to heat up samples to austenization temperature (1000 degC) at a heating rate of 10 degC per second...

09 October 2019 5,325 3 View

Are there any relevant work on impact-abrasion wear testing?

I am working on a project involving studying the impact-abrasive wear during grinding. I am interested to know if there are any relevant papers that has studied or tested impact-abrasive wear of...

08 September 2019 6,970 2 View

Can MATLAB be used to simulate nano or micoindentation by Berkovich or Vickers?

Can 2 dimensional simulation of indentation be done using MATLAB? if yes, I would really appreciate guidance from experienced MATLAB users !! Thank you

10 November 2018 2,043 2 View

What can be the reason for reduction in hardness and toughness of thin films or coatings due to doping with silver (Ag) ?

I have deposited pure Cr and W films by unbalanced magnetron sputtering method and then prepared films by doping them with Ag. The hardness and modulus of these coatings are lower than that of the...

01 February 2018 5,046 10 View

Does the presence of excess lattice oxygen in thin films or coatings signify high surface energy of the films or coatings?

In cerium oxide coatings, I have found that there are excess lattice oxygen when oxygen to metal ratio is quite high. Does it mean that the coatings have higher surface energy when there is excess...

31 December 2017 4,995 3 View

Can anyone kindly suggest me where to start learning simulation/modelling of Nanoindentation?

I would like to learn FEA method for nanoindentation for materials. I would really glad if someone would suggest as to where I should start learning simulation/modelling.

05 June 2017 6,901 4 View

How to calculate the adhesion energy of coatings from progressive load scratch testing?

Is there any procedure for calculating the adhesion energy of coatings by progressive load scratch testing. The samples are CrAlN coatings on tool steels.

02 March 2017 5,436 0 View

What is the heat of formation of Titanium oxynitride at 298K ?

I am looking for thermodynamic data on titanium oxynitride and chromium oxynitride and their heat of formation ?

08 September 2016 10,102 1 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

The Curse of Evolution and Complexity?

Brain and body mass together are positively correlated with lifespan (Hofman 1993). The duration of neural development is one of the best predictors of brain size, and conception is the best...

05 August 2024 6,247 3 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Emil Hristov Yankov

Hello Mohammad Shahrear Kabir,

This "synovial fluid" can be done in a homologous laboratory and chemical laboratory. It can also be purchased from a pharmacist working in a pharmacy.

Wishing for success in scientific work.

Emil Yankov

Peter Farrington

Did you see this paper?

Lubricants 2015, 3, 664-686; doi:10.3390/lubricants3040664