TGA
Katalizör madde esnasında alınabilir.
Şükrü Aktaş thank you
This depends on what you want to learn from TGA. Analysis before calcination can determine the best temperature range for the calcination. Analysis after the calcination gives information on thermal stability of the calcined sample.
Dear Wedad A. Alwesabi
TGA should be measured after attaining the desired material.
The mass composition can be obtained through this, and it doesn't make sense before calcination (i.e., before attaining the desired material).
Thank you
Pavar Sai Kumar thank you
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,788 4 View
I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture
14 July 2024 7,702 2 View
I prepared h-BN by hydrothermal methods by boron anhydride and urea after hydrothermal I was heated at 800 temps for 12 hours after that my sample stuck to the crucible the third time, and the...
15 May 2024 7,354 0 View
I fabricated nanocomposite using the sol-gel method with a mole ratio (1:1) I want (10g) of the final product ZnO-TiO2( molar mass-161.246g/mol) the calculations of the raw materials are as...
13 May 2024 1,731 5 View
i prepared graphene oxide by modified hummers method
13 May 2024 5,162 2 View
MgO NPs were synthesized by sol-gel method. i got Raman peaks at 1022 and 1400
09 May 2024 1,026 3 View
I need this synthesis by hydrothermal method
06 May 2024 1,866 4 View
Actually, I prepared a large amount of MgO, after aging I kept it in a hot air oven at 120 for 12 hours, but there was still moisture there, then I kept it again in a hot air oven at 120C for 6...
05 May 2024 6,279 2 View
because I prepared magnetite by sol-gel method, I got XRD peaks, but for Raman, I didn't get a peak at the range 600cm-1, should I change the wavelength of the laser, or what do I have to do
05 May 2024 2,244 4 View
microwave
16 April 2024 10,006 4 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,098 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,136 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,769 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,427 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,936 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,104 4 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,987 3 View