Please, is it important to convert MgO nanoparticle powder to pellet for getting peaks of Raman spectrum?

More Wedad A. Alwesabi's questions See All

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,788 4 View

Hello, please if any researcher work in ion battery help me,?

I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture

14 July 2024 7,702 2 View

Please, give me the correct syhtesis process for hbn and what is the raman range for h-BN ?

I prepared h-BN by hydrothermal methods by boron anhydride and urea after hydrothermal I was heated at 800 temps for 12 hours after that my sample stuck to the crucible the third time, and the...

15 May 2024 7,354 0 View

Hello, I need to ensure that my calculation for the amount of ZnO-TiO2 nanocomposite is right or is there a mistake, or there is another way?

I fabricated nanocomposite using the sol-gel method with a mole ratio (1:1) I want (10g) of the final product ZnO-TiO2( molar mass-161.246g/mol) the calculations of the raw materials are as...

13 May 2024 1,731 5 View

Hello, what the value of Id/Ig ratio for graphene oxide should be?

i prepared graphene oxide by modified hummers method

13 May 2024 5,162 2 View

What are starting material for hBN powder synthesis ?

I need this synthesis by hydrothermal method

06 May 2024 1,866 4 View

Hello,I prepared MgO NPs by sol-gel method, for raman spectroscopy what range should i use? because i used (100-900) but there is no peak?

Actually, I prepared a large amount of MgO, after aging I kept it in a hot air oven at 120 for 12 hours, but there was still moisture there, then I kept it again in a hot air oven at 120C for 6...

05 May 2024 6,279 2 View

Which type of laser and laser power appropriate for Raman for magnetite Fe3O4?

because I prepared magnetite by sol-gel method, I got XRD peaks, but for Raman, I didn't get a peak at the range 600cm-1, should I change the wavelength of the laser, or what do I have to do

05 May 2024 2,244 4 View

Hello, please , can we use the microwave oven which used in kitchen for drying the sample instead of the hot air oven?

microwave

16 April 2024 10,005 4 View

Why the sample get evaporation when keeping it in tube furnace with Ar gas?

rGo by heating GO sample is getting out by tube

02 April 2024 1,719 1 View

Is there a problem with my RNA pellet?

Hello, I am currently having problems with RNA extraction. I am using mouse liver (C57BL6J), and I have extracted RNA from mouse liver before. Before this experiment, my final RNA pellets were...

11 August 2024 7,080 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,176 3 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,065 0 View

Why is my ASO degraded quickly on agarose gel?

I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...

06 August 2024 3,129 2 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,152 4 View

What are possible strategies can be used to analyze data under sequential explanatory mixed method approach?

Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches

04 August 2024 2,701 6 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,366 2 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,464 0 View

I'm optimizing a tetra-ARMS PCR protocol with amplicon sizes: 165bp, 123bp and 93bp. Why, in the gel, only 165bp is visible while I'm expecting all 3?

It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...

01 August 2024 4,671 4 View

How to increase protein lysate concentration?

I am trying to prepare samples for IP. The pellet size is good and I am using 1% Tx-100 and using a syringe to further lyse the cells and maintain protein-protein interactions. I keep having a...

01 August 2024 7,199 1 View

Abdelhak Maghchiche

No, it is not necessary to convert MgO nanoparticle powder to pellets for obtaining peaks in the Raman spectrum. This method can be applied directly to the nanoparticle powder without the need for pelletization or any other form of sample preparation

Chiranjit Chaliha

Dear Sir, making a pellet is not that significant as Raman spectroscopy can be done both for nanoparticles as well as pellets.

Wedad A. Alwesabi

Chiranjit Chaliha thank you