When modeling a irdge in abaqus and you want to find the deck deflection, do you use U or, UT ?

Mohammed Ahmed @Mohammed_Ahmed223

04 April 2018 0 5K Report

Hello All

when modeling a Birdge in abaqus and you want to find the deck deflection, do you use U or, UT ?

Thanks

Badges
Science topic

Similar topics
Engineering
Modeling

More Mohammed Ahmed's questions See All

Bridge Abutment effect on flow field and/or Velocity Field ?

I am looking for a mathematical relationship to approximate the location at which abutments start affecting the flow field or velocity field of the current. Basically the distance where the...

06 July 2018 4,117 1 View

Maximum shear stress in Abaqus ?

I have modeled a Steel I-girder bridge with a moving load in abaqus, i need to extract the maximum shear stresses fro each girder. is it the S, Mises or S11 S12 S22 S33 depending on my orientations??

03 April 2018 1,474 3 View

MPC modeling problems in Abaqus ?

Hello Everyone, I am trying to model An integral Abutment bridges in Abaqus CAE, the bridge is fairly simple, a concrete deck resting on 10 Steel (I-Beam) girders. i am having a lot of problems...

31 December 2017 2,318 1 View

Abaqus MPC contact Issue??

Hello every one I am trying to create a connection between a concrete deck defined as a shell and steel girders defined as wires, i have chosen to do this by creating an MPC connector type beam....

10 November 2017 3,091 0 View

Abaqus error, when trying to apply contact and constraint between shell and beam????

Dear all, I am modeling a deck on steel i girders but whenecer i define the contact and the restraints i get these 3 errors, how can i fix it I keep getting this error For *tie pair...

07 August 2017 4,392 0 View

Modeling Contact between shell elements in abaqus?

Hello everyone, i am currently modeling a steel i girder bridge in abaqus, i would like to know how to model the contact between the girders and the bridge. there is a total of 10 girders that all...

07 August 2017 6,546 1 View

SAP2000 moving load????

hello guys, when modeling a moving load (truck) on a bridge in sap2000 , and you choose say the full 3 lanes how does sap run the trucks, i.e does sap run the trucks on three lanes simultaneously...

06 July 2017 8,416 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View