Hi
I'm a master geotechnical engineering student and I can't work in the lab for personal reasons . I will be grateful if anyone suggest me a topic that can be done by numerical modelling .
You can choose any of the following problems:
1. Soil-structure interaction problems such as modeling of soil-pile interaction problems
2. Analysis of seepage problems in unsaturated soils
3. Numerical modeling of triaxial/direct shear tests/consolidation tests
thank U professor Sazzad , could U please give me a more specific topic on number 2?
Hi Pedram Akbari,
If you do not do the experiment, you will study a geotechnical problem whose test data are available in the literature.
You must to look for a material that has been studied experimentally in the same frame of your numerical study such as :
elasticity, elastoplasticity, viscoelasticity, viscoplasticity problems
Hi, everyone This figure depicts a simulation of an electrostatic energy harvesting system in COMSOL Multiphysics software. My question is regarding the relationship between the changes in...
19 July 2024 4,694 4 View
I want to trap fluid (water..) in the PDMS channel for a long time. After a short period, the channels become empty of fluid. Is there a way to reduce the permeability of PDMS?
17 June 2024 2,703 4 View
I want to make sure the microchannel in my microfluidic device is filled with NaCl electrolyte. Because the color of the NaCl solution is bright, I can't be sure with my eyes. What substance can I...
21 April 2024 8,734 0 View
I am working on biological selenium nanoparticles. I have a question related to labeling method of selenium nanoparticles with radiopharmaceuticals. How to achieve a yield above 90%??
17 March 2024 6,991 0 View
Hi In this simulation, i noticed that i have a electrical field inside a conductor almost in range of e-11. this upper plate is connected to 10volt (DC) and by time dependent study it moves...
13 March 2024 1,669 1 View
hi anyone I used electrical circuit module and i have a resistor for measuring the power of the energy harvester. how can i measure the average power in this simulation?
05 March 2024 1,565 3 View
Can you guide me about this topic? I have a sample with 180 HV (HV0.3), which consists of coarse and fine pits of different depths, and I want to check local hard zones possibility by measuring...
26 February 2024 7,538 7 View
Hi everyone, I plan to work on a stramtable (a physical model) to model a river. As I used to work on open-channel flumes, I was curious about the flow measurement. The depth and average velocity...
14 February 2024 336 2 View
I am trying to compute the dissimilarity for species-trait matrix and for community-trait matrix. the two method of Gower distance and Bay-Curtis dissimilarity show virtually the same outputs for...
27 January 2024 2,723 0 View
I need a source for functional traits of gastropods and bivalves, specially life history traits. but i think the benthic species of my study area ,which is mangroves of northern Indian Ocean, are...
08 January 2024 9,782 7 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View