What should be molecular weight and copolymer constant of acrylic acrylamide copolymer used as a clay binder?

01 November 2023 1 2K Report

Acrylic Acrylemyde copolymer used as a binder in ceramic industry. What should be its copolymer constant and m.w. to get better performance?

Hassan Dawjee

I would say 4500 - 6000

Badges
Science topic

More Ashvin Patel's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Is there a specific FTIR figure if epoxy/ polysufide reinforced with Sic?

I have a copolymer if epoxy and rubber reinforced with Sic. I want a standard FTIR figure in transmittance mode.

20 June 2024 6,606 2 View

How to calculate the conversion of random copolymerization mixture?

I'm working on the RAFT copolymerization of MPC and NIPAm monomer, but I'm not sure how to calculate the total conversion from proton NMR? Is it an average of conversions of two monomers or just...

10 June 2024 7,430 2 View

How water soluble polymers act as good adsorbents for pollutant removal?

When a polymer is soluble in water, how is it able to interact with the adsorbate molecules dispersed in the solution? I need some logical explanation regarding this phenomenon along with relevant...

20 May 2024 6,116 2 View

Size acrylamide pores?

Good evening, I was wondering what is the size of Acrylamide/Bis-Acrylamide in a PAGE 4%/8%. I'm asking because after the run I found that some of the sample stayed in the well

04 May 2024 1,566 3 View

What is the best solvent to precipitate a lactide macromonomer?

I'm trying to remove acrylamide and lactide from the medium that didn't react to form the macromonomer

29 April 2024 4,903 1 View

Mechanism of copolymer?

Kindlly provide links or literature about the mechanism of free radical copolymerization of styrene and methacrlate, kinetics and rate equation

27 April 2024 404 2 View

What's wrong with my 12% SDS-PAGE gel?

Cannot separate between 10~25kD, always have a line around 25kD... (Resolving gel buffer: 30% Acrylamide/Bis, 1.5M Tris-Cl, pH 8.8, 10% SDS, 10% APS, TEMED)

22 March 2024 8,724 3 View

What method is for the purification of DNA band stained with silver nitrate from acrylamide?

I want to extract and purify a band from an acrylamide gel stained with silver nitrate and send it for sequencing. Every method (including solution in water, solution in TE, crush and soak method)...

22 February 2024 1,065 2 View

Can any one help to figure out the issue that i am facing while preparing polymer membrane ?

What solvent should be used to precipitate out the copolymer of vinyl pyridine and vinyl carbazole in NMP.I tried deionised water,ethyl acetate everything but unfortunately it doesnt get settle down.

08 February 2024 4,831 4 View

SDS-Gel separating gel polymerisation issues?

Recently we’ve noticed these patterns on our separating gel 15% and I’m wondering if anyone can provide insight into it. Is it normal? And if it isn’t what could we possibly be doing wrong? We’ve...

28 January 2024 3,029 5 View