Can anyone tell me how to find % anstase and rutile TiO2 by XRD analysis?

07 August 2016 3,112 8 View

Can anyone tell me how to find 001 facet in TiO2 from HRTEM data?

I know to find hkl values for anatase/rutile TiO2(101,004 etc.). I want to find 001, 010, facets from same data. Can anyone suggest method or some software for that? And if you have standard data...

09 October 2015 4,922 0 View

Can anyone provide me standard values of peaks in xrd spectrum for TiO2?

I want to know standard peak values for TiO2 using jcpds card.

10 November 2014 4,053 4 View

How can I find the phase type and hkl values from SAED pattern of metal oxide?

10 November 2014 745 1 View

No title

10 November 2014 6,719 6 View

How do I perform a visible light degradation experiment in the lab?

06 July 2014 6,685 3 View

Is ball-milling TiO2 with thiourea at low temperature a method for n-doped TiO2?

06 July 2014 7,715 4 View

How does one find doping concentration in metal oxides?

06 July 2014 5,501 6 View

For TiO2, what all information is taken by using BET surface area method?

That is entire isotherm run for pore size, pore volume, etc. is required or just surface area value with three points is enough?

05 June 2014 569 5 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

Uncertianiny in using dry or wet basis in mixing a sediment with fuel oil?

Hello I'm currently working on a topic related to studying the anaerobic biodegradation of TPH in marine sediments. In this work, sediment should be mixed with fuel oil to a concentration of 20 g...

24 February 2021 9,839 3 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View