28 May 2025 0 5K Report

Related to the article: ''Estimating the value of new antibiotic treatment strategies in Zhejiang province, China: cost-effectiveness analysis based on a validated dynamic model''

More Juhi Panday's questions See All
For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View

How to resolve ‘[ atomtypes ] Invalid order for directive atomtypes’ error in Gromacs?

I have been using Gromacs 2021.7. I wanted to simulate two small molecules in water. But, while generating the ions.tpr, I am getting the following error. The topol.top and .itp files for each...

17 July 2024 9,897 4 View

How to optimize nanoonions in quantum espresso?

I have a structure of nanoonion which is basically fullerene units with different number of carbon atoms structured like the onion (possessing common centre). So there are no repetitive cell unit....

21 August 2023 6,543 2 View

Should there be separate legislation to recognise liveinrelationships in India? Whether the child born out of such relationships should be maintained?

Maintenance of children born out of live in relationships

29 June 2023 6,192 4 View

Geology of upper mustang (Lomanthang)?

geological and historical importance

29 March 2023 3,634 2 View

How can I publish my thesis?

i want to upload the pdf of my thesis . I asks for authors. and then a list of my contacts who have a research gate account appear. I am the author. What must I do to get my pdf published...

22 February 2023 3,197 2 View

I would like to know the essential difference between a wave study and a longitudinal study, how would study design differ as per research question?

If the data for a study (especially in social science context) are collected at different time periods (say t1, t2 and t3), does it qualify as a three wave study or a longitudinal study? What...

08 December 2022 4,461 0 View

Need suggestion for the design of mixing vessel for difficult to discharge material ?

It's Latex and Carbon Liquid Liquid mixing which gets form solid in mixing tank which knows as rubber crumb with water in it. Problem is this material is not coming from the bottom of mixing tank...

17 September 2022 4,098 0 View

Can I use Plasmodb database to extract and analyze single cell RNA-seq data for Plasmodium?

Hello everyone, I am working on some set of genes of Plasmodium parasite and wanted to extract and analyze their gene expression data on wild type parasite and mutant ones. So I am designing the...

28 June 2022 5,024 0 View

BIOVIA remote server while enabling additional features is not connecting?

Hello everyone, Can anyone guide me in connecting with the BIOVIA of Dassault system. I am trying to connect with the remote server while enabling additional features and i am getting an error of...

02 May 2021 7,618 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close