What percentage of error will the assumptions carry in analysing temperature distribution in Electro DIscharge Machining (EDM)?

Jonnala Subba Reddy @Jonnala_Subba_Reddy

04 April 2018 0 350 Report

What percentage of error will the assumptions carry in analyzing temperature distribution in Electro DIscharge Machining (EDM) Process? The assumptions will simplify the model. How do we calculate the percentage of error after analyzing with experimental data? What is the expected tolerance in estimating temperature distribution and heat transfer rate? And consequently, The responses like Material Removal Rate, Tool Wear Rate, Surface Roughness and other metrological properties?

Badges
Science topic

More Jonnala Subba Reddy's questions See All

What is the influence of literature review for any journal paper? How do acess the quality of the paper based on Literature Review?

03 April 2019 3,404 4 View

Can we write any journal paper without a single reference?

Is it acceptable to write a paper without any reference? If so, will it be accepted? Can we write one page journal paper? To the point discussion would be possible or not? What are the...

10 November 2018 9,543 1 View

What is the social responsibility of the Research Scholor and doctoral candidate?

How far the research is being utilized for social cause? Is research given more importance than it is supposed to be given? How far these research papers, articles, letters etc. influence the...

04 May 2018 4,562 9 View

Can the "Conclusions" section be written lengthy or precise in a paper?

Is it good to write the "Conclusions" section lengthy or precise in a journal paper? Kindly suggest.

04 May 2018 7,226 17 View

Is there any good coupling interfaces available for ANSYS (FEM) and Electro Discharge Machining (EDM)?

Is there any good coupling interfaces available for ANSYS (FEM) and Electro Discharge Machining (EDM)? The heat transfer rate across the plasma zone, the temperature distribution along the...

04 May 2018 7,677 3 View

What is mental trap (The situation where we get struck while doing our research or a jouranl paper etc.) ? How to overcome the mental trap?

The mental trap or struck in between while doing the research work or writing a journal paper occur often in our life. We often get confused how many papers should be referred for writing a paper....

04 May 2018 4,538 3 View

Is it fair enough to publish experimental data in a peer reviewed journal? Or is it better way to publish data with graphs without publishing data?

The experimental data is the necessity in analyzing our responses w.r.to different influencing parameters. But it is observed, in recent past, most of the researchers are publishing graphs and...

04 May 2018 6,692 8 View

What is the influence of electrode in EDM when it is cut / drill deep into the workpiece?

As the depth of cut increases in EDM process, the over cut on the material also increases because the spark is generated round the electrode. What precautions should be considered in designing the...

04 May 2018 4,339 2 View

What is the temperature range in plasma zone in EDM process?

The plasma zone is the cause for removing the material from the work piece as well as from the electrode. What could be the temperature range of plasma during Electro Discharge Machining (EDM)?...

04 May 2018 6,145 1 View

What is the correctness of Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Energy Dispersive X-ray Analysis (EDX)?

What is the correctness of SEM, TEM and EDX analysis? What is the percentage of error? How do you calibrate the machine? I have got some data from the internet source. I request suggestions from...

04 May 2018 2,531 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View