What is the values of unit weight of sheet pile wall, modulus of elasticity in direction 1and 2, poisson ratio used to simultate as plate in program?

01 November 2022 0 10K Report

The sheet pile wall is simulated as a plate element, when enter the properties such as modulus of elasticity in direction 1and 2 poisson ratio and unit weight. I need typical values for these properties.

Badges
Science topic

More Hassan Obaid Abbas's questions See All

What is the difference between mathematical R^4 space and physical 4D unit space?

We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...

10 August 2024 6,678 14 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,291 2 View

How to use Density Functional Theory to calculate carrier mobilities of solid system?

Hello, everyone. I have tried to determine carrier motilities of some materials, by Density Functional Theory, using Quantum ESPRESSO. There are a few methods to do it, like a package called...

04 August 2024 8,894 1 View

Is it true that the vacuum bomb is about to arrive?

We assume this to be true. We also assume that the vacuum bomb is the latest version of explosives with an explosive power of a few to ten kg of TNT equivalent. It has the unique characteristic of...

04 August 2024 4,534 1 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

Can we find a statistical matrix mechanics equivalent to the Schrödinger equation?

We assume that we can find a statistical matrix mechanics equivalent to Schrödinger's PDE in two consecutive steps: i-Transform the Schrödinger PDE describing the wave function Ψ into its square...

27 July 2024 3,959 4 View

Has anyone looked into the stability of FEM methods on curved meshed?

Google scholar isn't giving me any results on this

27 July 2024 595 2 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Publishing a checklist?

Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...

01 August 2024 6,134 2 View

HEC 1A & HEC1B Cell Lines?

Hi, Kindly guide me that how many cells of HEC1A & HEC1B Cell lines should I seed for Wound healing assay and which plate type is recommended 6, 12 & 24?. Articles suggested mainly 24...

20 July 2024 4,143 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

How can we simulate(with FEM) the shape of Mobius strip using Abaqus Learning edition?

Aim is to simulate the shape of Mobius strip (an elastic ribbon) in simple way ( using Abaqus Learning edition). In literature, Mobius strip is modeled as Kirchhoff Rod / Cosserat plate. But, such...

15 July 2024 4,388 1 View

How to calculate CFU/m3 in settle plate?

14 July 2024 1,816 1 View