What is the solubility limit of TiN in CrN lattice ?

More Mohammad Shahrear Kabir's questions See All

What software would be best to simulate impact environment ?

I am trying to investigate the impact nature of steel balls (4 cm diameter) on steel plates. Which modelling software would be best to study the stress fields generated or any type of failure...

11 December 2019 1,943 4 View

What is the optimum austenization hold/soak time for cast structures?

I am looking for studies related to austenization soaking times and ways to reduce the time to achieve full dissolution of carbides as well as not to obtain austenite grain growth. Grain growth...

10 November 2019 4,824 3 View

Are there any studies regarding fully pearlitic/eutectoid steels with relation to soaking time during austenization ?

I am working on developing fully pearlitic steels with fine interlamellar spacing. I am going to heat up samples to austenization temperature (1000 degC) at a heating rate of 10 degC per second...

09 October 2019 5,325 3 View

Are there any relevant work on impact-abrasion wear testing?

I am working on a project involving studying the impact-abrasive wear during grinding. I am interested to know if there are any relevant papers that has studied or tested impact-abrasive wear of...

08 September 2019 6,970 2 View

Can MATLAB be used to simulate nano or micoindentation by Berkovich or Vickers?

Can 2 dimensional simulation of indentation be done using MATLAB? if yes, I would really appreciate guidance from experienced MATLAB users !! Thank you

10 November 2018 2,043 2 View

What can be the reason for reduction in hardness and toughness of thin films or coatings due to doping with silver (Ag) ?

I have deposited pure Cr and W films by unbalanced magnetron sputtering method and then prepared films by doping them with Ag. The hardness and modulus of these coatings are lower than that of the...

01 February 2018 5,046 10 View

Does the presence of excess lattice oxygen in thin films or coatings signify high surface energy of the films or coatings?

In cerium oxide coatings, I have found that there are excess lattice oxygen when oxygen to metal ratio is quite high. Does it mean that the coatings have higher surface energy when there is excess...

31 December 2017 4,995 3 View

Where can you purchase synthetic/artificial synovial fluid or anything that closely resembles synovial fluid?

I am designing experiments to study the tribological behaviour of coated Ti6Al4V in synovial fluid. Any help would be highly appreciated.

10 November 2017 2,496 2 View

Can anyone kindly suggest me where to start learning simulation/modelling of Nanoindentation?

I would like to learn FEA method for nanoindentation for materials. I would really glad if someone would suggest as to where I should start learning simulation/modelling.

05 June 2017 6,901 4 View

How to calculate the adhesion energy of coatings from progressive load scratch testing?

Is there any procedure for calculating the adhesion energy of coatings by progressive load scratch testing. The samples are CrAlN coatings on tool steels.

02 March 2017 5,436 0 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View