13 September 2016 3 8K Report

Hi to all,

When simulating faults in a transmission line using Matlab/Simulink, we can change inception angle by varying the time in the three phase fault breaker bloc.

My question is about the mathematical relationship between time and inception angle?

Regards

More Toufik Sebbagh's questions See All
I would like to know how to add a metallic layer (introduce these parameters) between semiconductor layers in the AMPS-1D software ?

how to enter the parameters of a metal layer in the AMPS-1D software

19 November 2020 3,824 1 View

Similar questions and discussions
Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is it possible for two human neuronal cell lines to have different gene sequence for the same protein?

I am looking at the ATP1A2 (Sodium/Potassium ATPase alpha subunit 2) in two human neuronal cell lines. Expression levels of this protein seems to be almost equal when detected by one antibody....

01 March 2021 3,607 3 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View

Do you need the CMV enhancer before the CMV promotor for a proper function of CMV on the gene that follows?

I'm a student and I have to produce a cell line with a knockin for the NRF2 gene with GFP. I have to put a promotor in front of the GFP because the gene will be too far away from the promotor of...

28 February 2021 7,127 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close