What is the testing protocol for a single cell PEM fuel cell?

Hello, I am going to test non-platinum catalyst material on the cathode side of my fuel cell. I have found out a protocol for testing but, it is published in 2009. So, I wanted to confirm whether...

09 October 2018 1,938 3 View

What are the possible ways to dope nitrogen in the graphene material?

I am planning to dope nitrogen in graphene which was fabricated by CVD equipment. Since at our lab we cannot use NH3 gas which is used to fabricate N-graphene, we can only fabricate graphene. Is...

02 March 2018 3,870 2 View

What is the most promising alternative non-PGM catalysts solution for LT-PEM fuel cells?

I have been researching on non-PGM catalysts for PEM fuel cells. I came to know that carbon materials like graphene and CNT's have high conductivity and suffers from corrosion. If we use carbon...

31 December 2017 9,516 4 View

Is PEM fuel cell membrane at the cathode side work in acidic or alkaline medium?

I guess it is acidic medium but Im not sure.

31 December 2017 178 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Which database would give me this list of chemical components?

Dear colleagues: I would like to know if anyone knows of a database that gives me the parameters pH, K, K, Mg, P, C, N, Zn, Cu, Ni and Cd of common foods. I find a lot of information of proteins,...

26 February 2021 5,525 3 View

Why is NH4OH added in heavy metals limit test?

The limit test I'm referring to is USP method II. In this procedure you need to dropwise add 6N of NH4OH to the sample until it the pH is alkali. After that you need to dilute and add HOAc until...

23 February 2021 2,049 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

No title

22 February 2021 9,932 11 View

The Role of Town Planners in CAV Use?

Colleagues and I are about to begin a project investigating the role of town planners and local authorities in establishing the introduction of connected and autonomous vehicles (CAVs). What...

21 February 2021 2,247 3 View

Can anyone help or comment on solubilising chlorobutanol in aqueous injections in minimum time possible?

Please suggest solubilisation of chlorobutanol in injections. Tried pH and high temperature. But the issue is of assay drop. If anyone can suggest any solution. Its a commonly used excipient for...

21 February 2021 7,397 1 View