What is the interaction of carbon graphite with PDMS? How to prepare carbon pdms composite?

More Ashton McNamara's questions See All

What is the best glassware or vessel to carry out microwave assisted preparation of graphene oxide?

I am looking at preparation of graphene oxide by microwave but when I used top and bottom, they break. Please help.

10 November 2017 6,196 4 View

Please help. We are working on a project to make CONDUCTIVE GLUE meant to replace soldering. it should be environmentally friendly?

Please give us idea on how to make conductive glue from waste or carbonized materials.

10 November 2017 2,164 3 View

Please help. We are working on a project to make CONDUCTIVE GLUE meant to replace soldering. it should be environmentally friendly?

Please give us idea on how to make conductive glue from waste or carbonized materials.

10 November 2017 3,079 2 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

Florian Pape

Hello,

we worked on SU8 - Fullerene Composites. A description about the process is given in our article: Article Fabrication and tribological investigation of fullerene C60/...

I guess for PDMS you can prepare it on a comparable way. I can send you a private copy of the article.

Best regards

Ashton McNamara

Thanks Doc. Please do send me a copy of your study. :) all the best!