What is the effect of furnace dimensions and volume on two samples with the same sintering process?

07 July 2021 1 8K Report

I am examining laboratory cases about the effect of furnace dimensions and volume. but I have no experience or data about that.

Abhinav Manish

the cooling rate has the most significant effect on the morphology transformation, while initial cooling temperature has more significant effect on the dimensional distortion than final cooling temperature. As to the mechanical properties transition from brittle to plastic, a more prominent effect of initial cooling temperature than cooling rate and final temperature was revealed.

Badges
Science topic

Similar topics
Methodology
Laboratory

More Meysam Kahkhaei Javan's questions See All

The effect of mold, mandrel and matrix error in hydraulic press machine on lamination defect of oxide ceramics?

If we divide the factors causing lamination defects in zinc oxide ceramic parts into two categories of equipment and materials. How much is the share of each? Can the conditions of the mold,...

16 April 2024 1,926 0 View

When we use the GEB option in MCNPX code?

If I'm not wrong, the GEB option in the MCNPX code is related to the Gaussian Energy Broadening. When do we use the GEB option in the MCNPX code?

08 March 2024 9,375 0 View

Static balance method?

static balance method?

17 November 2023 8,832 1 View

CMOS circuit design?

Design of CMOS circuit to create the signal Vsig. The supply voltage is Vdd and t1 is a delay which is equal to 5ns. The picture is attached.

19 August 2023 8,893 1 View

What is the reason for the "No air pressure" error in the atomic absorption spectroscopy?

Our laboratory has a PerkinElmer (model: AAnalyst 800) atomic absorption spectroscopy. Recently, the performance of the device has encountered a problem. When the circuit breaker of the device...

22 June 2023 4,230 4 View

What are the advantages of counting photons over calculating energy they deposit in detector pixels?

What is the advantages of counting photons over calculating energy they deposit in detector pixels in dual high-energy X-Ray radiography?

13 June 2023 6,340 2 View

Low-power and ultra low-offset CMOS comparator?

I need a comparator with an offset of less than 5 mV. It is better to be designed in 0.18 um CMOS technology and the dimensions of MOSFETs should be clear. Thanks.

01 February 2022 4,640 2 View

How can the two parameters of electric current and wire feed rate be independent ?

I am optimizing the thermal spraying process by device parameters such as current, voltage, atmospheric pressure, nozzle type and wire feed rate. How can the two parameters of electric current and...

08 October 2021 2,943 0 View

Is it okay to report Standard deviations greater than the means?

I have this data set about the concentration of aflatoxin in maize. most of the means have very high SD. What should i do about this when reporting?

08 June 2021 8,975 7 View

What is the best lubricant and dispersant for SiC abrasive particles ?

I am examining laboratory cases about ZnO Based ceramic Lapping with SiC,Al2O3,CeO2 and SiO2 abrasive particles. but i have no experience about modifying SiC slurry lapping. Also,i use of double...

13 December 2020 4,524 4 View

Project/Experimental assistance ？?

Do experiments on behalf of Our Business: Laboratory animal rearing Animal modeling Experimental animal behavior detection, image ultrasonic detection, electrophysiology platform Organoid...

05 August 2024 5,829 1 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Non -oxidizing metal binders?

I'm trying to sinter some Nb parts and I'm trying to find a binder which does not produce oxidative compounds when it decomposes.

25 July 2024 9,823 3 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

How are clinical and environmental yeast/fungal strains stored usually in mycology laboratories?

I understand a glycerol stock for long-term preservation would be ideal, but how are working cultures generally stored? Mainly concerning Candida spp. isolates. A few references mention that they...

22 July 2024 6,592 3 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How to change the author?

Hello! Research of factors affecting thickness of the covering obtained by electro contact sintering of composite materials. This is my article, not Varvara. How to change the author? Incorrect...

09 July 2024 3,829 0 View

What is the method of standard curve of IAA preparation?

Hi, I should prapare a standard curve of IAA and I don't know the method is. For measuring of IAA in bacteria, I culture bacteria in TSB medium and mix the supernatant of inoculated medium with...

29 June 2024 4,421 1 View

What may cause whitish discolor of polycrystalline diamond surface, and cracks near edge?

I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...

23 June 2024 7,758 2 View