What is the effect of electrode on the polarization-elelctric field loop (PE loop)?

08 August 2017 0 5K Report

Is it possible to get loop even though sample is nonferroelectric because of artifact? To what extent the loop is reliable.

Badges
Science topic

More Alaka Panda's questions See All

How to confirm the phase transition from R3c to orthorhombic?

Indoors BiFeO3 has r3c st and with doping it goes to orthorhombic. But the exact orthorhombic structure group is not clear.which is correct r3c to pbnm or r3c to c222. How to check it appropriately.

11 December 2018 9,000 3 View

Anyone here using PE loop tracer system from Marine India?

Please inbox me. I have some queries regarding the instrument. Thank you in advance. Regards Alaka

10 November 2018 4,710 0 View

Can anyone suggest me if the attached result signifies the ferroelectric behaviour ?

I am herewith attaching the PE result (ferroelectric hysteresis) with finite loop area. I need suggestions regarding following 1. As can be seen the loop ahifted to left from origin and some cases...

31 December 2017 9,218 9 View

What does it mean when Zero field cooled (ZFC) and field cooled (FC) curve completely merge with each other?

what does the peak observed in ZFC and FC imply? how does it related to spin glass transition? How to confirm the same? Can anyone please suggest me.

05 June 2017 1,554 4 View

What will be the effect of impurity on Dielectric properties of semiconductor?

How does the morphology of impurity affects the dielectric properties. The impurity phase is Hematite so can anyone suggest or refer some literature regarding this.

05 June 2017 8,482 8 View

Does increase in peak shifting with higher 2 theta angle in XRD logical?

I am observing the shift in peaks in a mixed phase system (2 phases). I observed the peak shifting is more at higher angles i.e if it is 0.2 upto 2 theta =30 degrees which increases to 0.4 towards...

05 June 2017 5,902 16 View

What does the enhancement of intensity of certain peaks in XRD pattern implies?

I am working on Bi2Fe4O9 sample which shows some planes getting enhanced after sintering. The specific planes are (001),(002),(140). Can anyone suggest what it is due to?

04 May 2017 5,768 5 View

Can I use any matrix for PE loop measurement?

PE measurement requires well sintered dense sample and I have small amount on which I want to carry out PE loop so is it possible for me to use any matrix in which i can disperse the sample and...

31 December 2016 7,983 6 View

Can anyone help me out on analysis of PE loop?

Here I am attaching the PE loops of my sample Bi2Fe4O9.Please help me out aor suggest some references to help me out in this

31 December 2016 8,391 0 View

ZFC FC data analysis?

I am working on Bi2Fe4O9 system and I am getting hematite impurity.Temperature dependent magnetization measurements shows almost same values at low T for both ZFC as well as FC. Can anyone please...

11 December 2016 1,299 0 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

I need the datasets of Microgrid for system identification?

Hi I am working on data driven model of the microgrid, for that, i need the reliable datasets for the identification of MG data driven Model. Thanks

02 August 2024 5,748 4 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

How to check pH of a high strength hydrogel?

We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...

30 July 2024 942 2 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

I need a reliable source or an example supported by excel sheet to understand Fuzzy Vikor?

27 July 2024 5,916 1 View

Why semicircle of nyquist plot is not complete?

While I am doing HER, I noticed that nyquist plots of Electrochemical Impedance Spectroscopy (EIS) is not complete. Will it affect for the Linear Sweep Voltametry (LSV) data? However, I can found...

26 July 2024 7,542 4 View

Why do these abnormal charge/discharge curves of coin cell batteries appear?

As shown in the figures, there are several abnormal charge/discharge curves.Each of them may have different problems. I am curious why these situations appeared differently?There are a lot of...

24 July 2024 6,930 1 View