Is there any guide how to write full research protocol?

Dear Research Community, I need to write full research protocol and I need help in suggesting the steps to follow and the template for it please, your guide is much appreciated Mohammed Abed, MD

20 June 2020 8,445 1 View

How can i define the USRP N210 on pc under windows 10?

How can i define the USRP N210 on pc under windows 10 and i used gnu radio 3.8.. i set the configuration and i make the ping and recived reply successfuly but i cannot define the device and an...

21 January 2020 1,442 2 View

What is the number of measurement required in Circulant and Toeplitz sensing matrix in general in term of N an M in compressive sensing?

what is the number of measurement M (the number of measurement vector that result from multiplication of sparse vector N with sensing matrix (NxM)) required when using Circulant and Toeplitz...

16 January 2020 9,666 2 View

How do I account for temperature fluctuations with daily averaged data?

The NASA Power data set gives access to daily or monthly temperature averages for any point on earth. This would be useful for calculating PV output given the reliance of efficiency of panels on...

07 December 2019 9,133 3 View

How can I use a pretrained deep network (e.g. GoogleNet or Alexnet) for a regression task on a new image dataset using Matlab neural tools?

using deep learning e.g GoogleNet , Alexnet or VGG19.

01 September 2018 2,358 3 View

What is the most effective way of cestodes staining ?

I need a procedure for good staining of cestodes

25 September 2017 3,976 4 View

Can any one help me to find the MATLAB code to compute pd (probability of detection ) in cyclostationary sensing technique in cognitive radio ?

14 September 2017 3,891 1 View

No title

Anti-Sinking Composite Materials for Ships.

10 July 2017 9,071 3 View

Fowl serum precipitin?

How can I enhance fowl serum antibody precipitin other than high salt concentration, is there anthor method? thanks

26 March 2017 3,207 11 View

Does anyone has questionnaire to measure ICU nurses stress level regarding the end of life care ?

05 January 2017 7,292 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View