I would want to know what kind of functional groups on the film allow it to bond to agarose. Basically, I want to coat different materials with something like gelbond, then pour molten agarose on them and have the solidified agarose be well adhered.
I am not sure. But I know that 3M is the original manufacturer. Maybe you can ask them?
Does anyone remember how to take a FISH image with Metasystems Isis software and then take another at a different focal plane and combine them? I used to do this but now can't remember! Thanks
14 May 2024 10,025 0 View
Oliver Wendel Holmes believed that justice had to do with customs that vary from one society to another, relativistic and without a foundation as an overarching principle. Marxist believe that...
22 March 2023 4,828 4 View
Recently I’ve started seeing these clumps in my primary MSC flask (T175). I first noticed these compact clumps in a flask near 80% confluence but I’m also seeing it in less confluent flasks. The...
22 February 2023 9,528 3 View
My lab has been using the Qubit ssDNA kit to quantify cDNA prior to qPCR input, but we have doubts about the accuracy of this kit. The MFR explicitly states that the Qubit ssDNA kit does not bind...
14 December 2022 1,052 2 View
It is said that the p value for a t-test can be calculated as one-tailed or two-tailed. This makes sense as Condition A scores can be higher, or lower than Condition B scores (so a two-directional...
04 March 2022 3,629 4 View
I have seen some literature discussing clearance of LPS from the bloodstream, where it can be cleared pretty well in about 6 hours (Lipopolysaccharide Is Cleared from the Circulation by Hepato......
05 August 2021 2,263 1 View
Traditionally patients in South Africa, particularly in rural areas retain their own clinical record, often in an exercise book or similar. Healthcare staff also record the history of a particular...
14 May 2021 3,930 3 View
Is it possible to have two protein variants transcribed from a transfected plasmid (or viral vector)? Not in the sense of using IRES or P2A/T2A, but rather in having two proteins with the same C...
02 March 2021 7,761 2 View
All suggestions welcome. We are curious to find out what works well, and to hear about diverse methodology. Thanks! We currently have restricted access to a lab where Silver staining etc could...
09 June 2020 9,263 3 View
If an MRI knee scan identifies a meniscal tear; what factors are taken into consideration to send for arthroscopy? If the scan has been generated from a GP referral: is there vetting to decide...
14 May 2020 352 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...
07 August 2024 8,414 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...
06 August 2024 3,176 0 View
I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...
06 August 2024 3,130 2 View
It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...
01 August 2024 4,673 4 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View
I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...
23 July 2024 4,461 1 View