Hi everyone
I am trying to coat a glass-bottom dish with Pam3CSK4 and plate THP-1 cells to measure IL6 with ELISA from the supernatant. I wondered if anyone knows a good concentration and incubation time for coating the dishes with Pam3.
Thanks
Hello Akram
Why don't you do a few pilot experiments if you have the resources with the following concentration and time of incubation.
Concentration of Pam3CSK4 :
Concentration range from 200ng/ml to 1000ng/ml.
Try three time points :
30mins, 1hour and 2 hours.
All the best.
I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...
16 February 2021 5,876 2 View
Hi every one I transfected Lamp-1 GFP plasmid to the HEK293 cell line. When I image the cells in TIRF, I see green fluorescence o the cytosol too. Does anyone have any idea that how it can...
21 December 2020 9,978 3 View
Hi every one I have made a cell line of HEK293 transfected LAPM-1GFP and after seeding the cells for 24h, I try to load dextran on the dish but after imaging, the cells with GFP+ have loaded less...
14 December 2020 1,801 2 View
I am working in research on climate adaptation so need to compare the performance of the urban fabric to the climate changes, which requires me to make a comparison and simulation of the...
03 December 2020 988 8 View
Dears, I have different variables in multiple regression. Two variables are highly correlated. To solve the collinearity issue, I dropped one of them from the multiple regression model. The...
29 November 2020 2,695 4 View
I need this because I have to represent it in a conference as a keynote speaker
17 November 2020 584 4 View
I want to synthesize iron nanoparticles with heparin, but I have trouble synthesizing First of all, do I have to use a freezer drying for drying of product and it is not impossible use from...
16 November 2020 9,455 2 View
It is easy to understand the meaning of relationship and effect (impact) in general. But when it comes to the statistical analysis it is a difficult conundrum, as one can determine the...
24 July 2020 6,525 7 View
We are aware of the fact that some type of solvent is required for isolating a compound from herbs. I personally believe that water is the best solvent since mostly decoction is prepared using...
22 July 2020 4,179 2 View
Hi everyone I have recently conducted an experiment my experiment design is like below: group 1 T1 X T2 T3 group 2 T1 X T2 T3 group 3 T1 X T2 T3 group 4 T1 X...
16 July 2020 7,837 2 View
Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...
03 March 2021 5,999 3 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...
02 March 2021 3,713 2 View
Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...
02 March 2021 3,584 1 View
I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...
02 March 2021 9,945 3 View
im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...
02 March 2021 2,246 2 View
Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...
01 March 2021 8,220 2 View
I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....
28 February 2021 7,967 3 View
28 February 2021 2,534 2 View
We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...
28 February 2021 1,149 1 View