Is there any restriction on the level of aluminium in rail wheel steel
Ansys Fluent has Lee Evaporation Condensation model which works for cases above saturation temperature. How can one use VOF with mass transfer UDF to solve this problem. If anyone can guide it...
06 July 2019 1,659 3 View
One of our plants make peritectic grade structural plates ( Carbon 0.15-0.17 %, Mn 0.8-1.1 %, Si - 0.2 - 0.3%, Al-0.03-0.04%). Recently we are noticing appearance of surface defects of the nature...
07 August 2018 1,033 1 View
Looking forward to using FLUENT for modeling droplet evaporation, breakup and coalescence during its flight towards a heated flat plate. Need help in looking for relevant literature from where to...
03 April 2016 9,238 1 View
For my work I am planning to model droplet mechanism during heat transfer from hot surface in film boiling regime for spray cooling by water. Need advice from experts, researchers on reference...
31 December 2015 9,862 3 View
Looking for softwares that can be used for predicting material properties of steel. Is there any open source software or academic software available as university designed programmes that can be...
09 October 2015 6,552 7 View
Is there any extensive literature, dataset or open source/free software for generating CCT and TTT diagrams for steels
09 October 2015 4,719 22 View
Recently we came across this kind of crack in rolled plate steel sample. Looking for a root cause analysis into the genesis of this crack. The attached document shows all the micrograph images of...
07 August 2015 3,668 5 View
Hi all, I have been scouring the internet to search for ways to track the interface in VOF multiphase flow modeling using UDF in Ansys Fluent. Looking for some suggestions from researchers here as...
01 January 1970 5,081 4 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I have reached out to the original creator Dr. Demerouti but have had no luck with a response. I am completing my IRB form and need the information or permission by tomorrow. I know short notice,...
29 July 2024 3,684 0 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
Good morning, I am trying to produce a recombinant protein. Unfortunately I one of the two restriction enzymes that I use do not cut at the end of the MCS. After the digestion 15 nucleotides of...
17 July 2024 2,787 4 View