What happens when pH value is less than 7 while preparing hydroxy apatite using wet chemical analysis?

More Reshma Kuppili's questions See All

What are the methods for analyzing trihalomethanes in water other than gas chromatography and liquid chromatography?

for monitoring disinfection byproducts in drinking water

12 October 2023 8,613 3 View

I am doing base hydrolysis of ester with LiOH and THF:H2O( 1:1) but after hydrolysis in acid NMR I am getting 4 proton extra peak?

4 protons peak may be CH2 near a heteroatom .

13 July 2023 1,075 1 View

How to reduce air bubble formation in film?

The film forming solution (FFS) is stirred overnight and it is oven dried at 40°C. Please give me suggestions to reduce the air bubble.

09 July 2023 7,857 4 View

Does anyone know how to prevent protein coeluting with other impurities in size exclusion Column?

I have been trying to purify a transcription factor. Protein has MBP and His Tag. I use His TRAP as my first purification step and then after I do size exclusion, but my protein (83 KDa) elutes...

23 April 2023 9,182 5 View

How to recover the Pd(PPh3)4 catalyst, already become dark brown?

How to store this catalyst?

06 March 2023 9,026 1 View

How do I determine doping concentration of a new element in Barium Titanate structure if I want to produce a new system?

I want to produce a new system of Barium Titanate and characterize it for high dielectric constant values at microwave frequencies.

02 February 2023 4,203 8 View

How to find Yaw joint angle of differential drive robot ?

I'm designing leader follower feedback controller for crawler robots .Here rear wheel is connected to front via a joint so that it can follow front when it turns ,for both the module(front...

20 December 2021 1,203 3 View

Multivesicular liposomes formulation?

multivesicular liposomes are prepared by double emulsification method. Can someone tell how to evaporate organic solvent from multivesicular liposomes preparation without emulsion cracking?

04 March 2021 5,166 3 View

What might be the reason for obtaining two bands in plant genomic DNA extraction?

I got a thin band and a thick band i guess it would be the genomic DNA and the 260/280 ratio is 3.

21 February 2021 6,871 6 View

Any recommendations for tetR antibody for IHC?

I am planning an experiment where I've to detect cells which are expressing TetR, my vector is so big that I can't have a reporter in it. I was thinking if I can detect the expression of TetR...

24 September 2020 1,293 4 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ?

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ? and can I use other tubes than Teflon for digestion?

04 July 2024 158 4 View

How do I make a solution from fibroblast growth factor since it is available as a powder?

I am using fibroblast growth factor, purchased in powder form. What suitable substance should be added to get it in a liquid form? Thanks

03 July 2024 9,866 2 View

How to remove aluminium oxide from powder ?

I synthesise intermetallic compounds through nickel and aluminium powders. But the pure powder after synthesis is difficult to obtain. Especially the presence of aluminium oxide very seriously...

01 July 2024 4,030 3 View

Emil Hristov Yankov

Hello Reshma Kuppili, When the pH of the solution is lower, the chemical reaction process changes. And the reaction with the sample material also changes. Therefore, the results obtained will not be adequate to the desired effect. It is good to adhere to prescribed experimental conditions. Comparative analyzes can then be made with previous studies. With respect Emil Yankov

Reshma Kuppili

Thank you sir