In ABAQUS/Standart there is Full Newton Method among the solution techniques. What deos Full Newton Method means? It means that "Incremental Iterative Newton Raphson Method" or "Newton Raphson Method".
Thanks in advance.
In ABAQUS/Standart there is Full Newton Method among the solution techniques. What deos Full Newton Method means? It means that "Incremental Iterative Newton Raphson Method" or "Newton Raphson...
08 September 2016 3,254 0 View
I have performed a simple 3D cantilever beam analysis in ABAQUS/Explicit. I carry out a major tensile force at the end of the beam, so i can see the fracture. In other words, the beam is divided...
05 June 2016 4,882 3 View
Does Abaqus software calculate stiffness matrix and mass matrix again and again in per step when a nonlinear dynamic analysis be performed. If the answer is yes, then the software must exclude the...
05 June 2016 4,784 4 View
How can be determined the value of "Maxps Damage" and consequently "fracture energy parameter of Damage Evolution" for concrete in ABAQUS?
05 June 2016 6,042 2 View
Dear All, I am modelling reinforced concrete structure by using concrete damaged plasticity model. I apply seismic loads. But when I increase the applied load, the displacements and stresses are...
04 May 2016 7,488 3 View
Hi, I want to simulate nonlinear dynamic analysis in ABAQUS and i will use "Concrete Damaged Plasticity" in my model. I want to know how to determine the value of "dilation angle, eccentricity,...
11 December 2015 8,688 8 View
Hi! I use Drucker-Prager yield criterion in Abaqus for concrete. There are "angle of friction" and "dilation angle" parameters in there. As far as I know, angle of friction resembles Mohr-Coulomb...
11 December 2015 9,032 6 View
I want to run statical analysis. But i can't assign hinge. Can anyone help me please? Thanks in advance.
09 October 2015 1,058 1 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Are there any statistical methods to justify your sampling technique using SPSS or AMOS?
05 August 2024 9,153 4 View
Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches
04 August 2024 2,703 6 View
Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...
31 July 2024 8,141 13 View
I am currently considering a research project focusing on a comparative analysis of starch metabolism in orchids and roses. I am particularly interested in identifying the types and quantities of...
30 July 2024 4,267 2 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...
29 July 2024 7,198 9 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View