I want to run statical analysis. But i can't assign hinge. Can anyone help me please?
Thanks in advance.
Dear Zucco;
For example i want to model truss system. Therefore firstly i draw my frame system but after then i can't assign hinges?
In ABAQUS/Standart there is Full Newton Method among the solution techniques. What deos Full Newton Method means? It means that "Incremental Iterative Newton Raphson Method" or "Newton Raphson...
08 September 2016 3,254 0 View
08 September 2016 2,656 0 View
I have performed a simple 3D cantilever beam analysis in ABAQUS/Explicit. I carry out a major tensile force at the end of the beam, so i can see the fracture. In other words, the beam is divided...
05 June 2016 4,882 3 View
Does Abaqus software calculate stiffness matrix and mass matrix again and again in per step when a nonlinear dynamic analysis be performed. If the answer is yes, then the software must exclude the...
05 June 2016 4,784 4 View
How can be determined the value of "Maxps Damage" and consequently "fracture energy parameter of Damage Evolution" for concrete in ABAQUS?
05 June 2016 6,042 2 View
Dear All, I am modelling reinforced concrete structure by using concrete damaged plasticity model. I apply seismic loads. But when I increase the applied load, the displacements and stresses are...
04 May 2016 7,488 3 View
Hi, I want to simulate nonlinear dynamic analysis in ABAQUS and i will use "Concrete Damaged Plasticity" in my model. I want to know how to determine the value of "dilation angle, eccentricity,...
11 December 2015 8,688 8 View
Hi! I use Drucker-Prager yield criterion in Abaqus for concrete. There are "angle of friction" and "dilation angle" parameters in there. As far as I know, angle of friction resembles Mohr-Coulomb...
11 December 2015 9,032 6 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View