What can be an optimum pouring temperature for an ASTM A439 d2, Ni-resist austenitic cast iron alloy?

More Nithin Raj's questions See All

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to enrich pig excreta for increasing nutrient quality organically ?

Pig slurry is rich in major and minor nutrients. Is there any way to improve / Enrich its manure quality to be used in agriculture organically ? please share your knowledge.

09 August 2024 5,605 2 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Leaf area of tomato ?

Hi How can this equation Ln(LA) = 1.038 + 0.89 ln(X) be applied to calculate the leaf area of a tomato? Can you explain with an example and what is the substitution of Ln and ln?

06 August 2024 2,508 2 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,805 3 View

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds?

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds

04 August 2024 3,019 3 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How to select target material for X-Ray generation?

Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?

31 July 2024 5,824 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

How are aPTT and PT values reduced after hemodialysis compared to before dialysis value in patients with chronic kidney disease?

I am conducting my research regarding blood coagulation in patients with CKD. I observed a reduction in post hemodialysis aPTT and PT values compared to pre hemodialysis values. But most of...

30 July 2024 3,467 0 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Sagarsingh Kushwah

You may find your answer at the following link:

https://www.pentictonfoundry.com/news/austenitic-ductile-iron-astm-a439-grade-d2-58-30-8/

Safwan al-qawabah

https://nickelinstitute.org/media/1770/propertiesandapplicationsofni_resistandductileni_resistalloys_11018_.pdf

Mohamed Ramadan

Optimum pouring temperature for 500kg ASTM A439 d2, Ni-resist austenitic cast iron is 50 o C to 70 o C above its melting point depend on casting thickness.