What are the predictable differences in characteristics between combustion and wet chemistry synthesised CuO nanoparticles?

25 November 2015 1 6K Report

I am interested to learn whether there are predictable differences in the characteristics of copper oxide (CuO) nanoparticles stemming from combustion vs wet chemistry synthesis methods and if yes what those would be (references are welcome).

Thomas Nann

The surface ligands. Particles made by wet-chemical methods always bear surface ligands, which might influence the properties significantly.

Badges
Science topic

Similar topics
Engineering
Modeling

More Moritz Volland's questions See All

What are good GPS trackers for recording the daily grazing movements of livestock?

I am looking for recommendations for GPS trackers to record the daily grazing movements of goats, cattle, and camels in the Mountains of Dhofar, Oman. In the past, I have used a tracker from...

18 December 2023 4,577 4 View

How to improve In-vitro transcription with T7 RNAP?

Dear colleagues, I'm currently running some in-vitro transcriptions with the HiScribe T7 RNA Synthesis Kit by NEB. As Templates I'm using a purified PCR product as a run-off template. I properly...

02 August 2023 3,741 5 View

Best Gel-electrophoresis system for mRNA?

Dear colleagues, I'm currently running some in-vitro transcription assays and I also want to check the quality on a denaturing gel-electrophoresis. However, though I have a sufficient...

26 July 2023 1,943 1 View

What would cause over-recovery of a spiked sample in plasma?

We ran a specificity/selectivity qPCR for plasma DNA samples. For specificity we added mastermix only into the plasma and had all samples come back with 0 signal (expected). For selectivity, we...

06 March 2023 1,470 0 View

Sideproduct of Grignard Reaction?

Hello Together, I made a Grignard Reaction in which I have replaced a chlorine with trimethylsilylacetylen. This reaction worked very well, but after the purification I had to find out, that...

13 July 2022 7,487 0 View

Selective amidation of carboxylic acid and primary amine in presence of secondary amine possible?

Hello everybody, I am currently trying to couple a building block which has a secondary amine group and a carboxylic acid group to a primary amine, in order to get an amide, while retaining the...

08 September 2021 4,740 3 View

Are there well-established collaborative sorting tasks/datasets?

Hi, I am currently working on research on communication behavior in Mixed Reality. I am planning a study, where dyads perform a task, in which they have to collaboratively cluster or sort cards...

31 January 2021 5,279 3 View

Is it possible in smartpls to plot a confidence intervall in an interaction plot?

Hi everyone, I am using smartpls3 to analyze my model and I have a significant interaction in this model. I know the general function of plotting this interaction, but I am wondering if it is...

01 November 2020 8,969 2 View

Can someone give me an example for a questionnaire regarding roger's innovations in organizations?

Hello, I am looking for a questionnaire based on Roger's Diffusion of Innovations - Innovations in Organizations theory. Can someone give me an example?

15 September 2020 8,641 4 View

Is there a way to find out the number of articles, which appear, when I enter a specific term at the search?

for example, i was searching for "chronic neck pain and resistance Training" and so many publications appeared for that Topic, but i can't find the exact number of articles, which appeared here....

25 January 2020 9,751 2 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,066 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Can i quantify a nanoparticle encapsulated in cell culture medium by hplc?

Hello, if you made a transwell assay where you incubate the cells with a nanoparticle-encapsulated drug and considering that in the oposite compartment you'll have both the free and encapsulte...

03 August 2024 2,730 1 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

What is the best practice for resuspending cell pellets during competent cell preparation (both electro and comp)?

I'm fairly new to making homemade comp cells and have done so with some mild success. What is generally an acceptable way of resuspending comp cells during wash steps? I've been told to swirl the...

31 July 2024 8,309 0 View