What are the possible efficient methods to decrease the temperature during grinding?

More Atul Babbar's questions See All

How can we mitigate the risk of osteonecrosis during brain craniotomy?

Generally, temperature rises during cutting and have adverse effects on adjacent neural tissues.

08 September 2018 717 0 View

What are different methods by which degradation rate of scaffolds can be increased?

I want to increase degradation rate of my specimens, what type of coating material I can use? Or any other method..

07 August 2018 2,732 0 View

Where i can learn soft computing techniques?

Which resources are useful to learn soft computing techniques?

03 April 2018 4,631 3 View

Which is the best optimization technique to get reliable results?

I want to optimize my results, which technique i should use? Genetic Algorithm Fuzzy logic Particle swarm optimization

01 February 2018 1,810 7 View

Suggest me a way or technique which will help me in real-time monitoring of temperature rise during grinding?

During the phase of grinding, i want to measure the temperature rise due to heat evolution during machining But in real-time.

01 February 2018 2,056 10 View

What are the recent trends in bio-manufacturing?

Bio manufacturing is a prominent field, what novel methods are used in this field?

01 February 2018 4,307 3 View

Which is the best software for research paper writing with correct English?

I want to use a software for writing research papers. Please suggest a software which can provide multiple journal formats and automatically modifies standard research paper as per the...

01 January 1970 2,797 3 View

How the wettability of rock sample can be changed by ageing in pure hydrocarbon oils only?

I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...

27 February 2021 5,383 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

How to remove compound ( Europium complex ) from paraffin oil?

How can I remove my compound from paraffin oil? Mistakenly my compound fell in an oil. Compound = Europium complex

22 February 2021 5,667 2 View

When I mix oil and NaOH solution, Why solid layer in the surface is formed?

During my trial for lubricant oil re-refinery process, I use NaOH as coagulant agent. After overnight of gravity settling, a solid layer in the surface was form. what product is that? since the...

22 February 2021 2,116 4 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

What reaction will occur when adding hexamine into ammonium nitrate in an acidic medium?

Hello, I am investigating properties of water in oil emulsion explosives. And adding hexamine (hexamethylenetetramine) into one of the phases that are used to make the emulsion should increase the...

21 February 2021 8,680 1 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

Can any one explain why the ethyl ester Biodiesel (FAEE) has higher than that of the metyl ester FAME- both of them are derived from the same oil?

Biodiesels derived from waste vegetable oil transesterification with Ethanol (FAEE) show higher peroxide values than those derived by transesterification with methanol (FAME) prepared under the...

13 February 2021 193 6 View

Oleg Nizhnik

Grinding is famous for its high waste heat. Simple parametric solution is to use coarser grinding wheel (you will need higher torque motor though). Or migrate to cutting - some of modern rotary saws (for example, from "Evolution" company) are notably producing very low waste heat and reduced number of sparks

Mushtaq Ahmad

DOC]control of grinding temperature by high speed air jets - TARA - Trinity ...

www.tara.tcd.ie/bitstream/2262/10919/1/Babic_Torrance_Murray.doc

by DM Babic - ‎Cited by 10 - ‎Related articlesProcedures such as HEDG (High Efficiency Deep Grinding) and HSPG (High Speed Peel Grinding) allow for both major metal removal and surface finish of ... There are several possible ways for theheat generated in grinding to dissipate. .... This can be verified by calculating the partition ratio, R, foreach test condition.

Daniel Martinez Krahmer

One way is to use a grinding wheel with higher porosity in combination with a high level of lubricant

Another way, if you have a CNC grinding machine is to reduce the cutting speed of the wheel and increase the feed speed of the machining part.

Manish Mukhopadhyay

Controlling the process parameters like speed feed and infeed can greatly effect the heat generation. Optimization of Dressing infeed also can be helpful to control the heat generation.