What are the methods to implement series capacitance in microstrip environment?

05 March 2019 1 10K Report

I want to implement series capacitance in distributed and transmission line based configuration. I have the values of the capacitance. What are the different methods to implement it?

Abdelhalim abdelnaby Zekry

Dear Debapratim,

I think one of the straight forward method is to make a make a slit or a cut an the transmission line perpendicular to its paths. This stems directly from the definition of the capacitor. If you want to increase its value to can a surface mount capacitor.

Best wishes

Badges
Science topic

More Debapratim Dhara's questions See All

Techniques regarding protein-protein interaction in vitro?

What techniques or assays will be used when a purified lyophilized powder is purchased from a company to study protein-protein interaction?

15 July 2024 1,598 3 View

What is the mathematical algorithm used for Sentinel 1 TOPS deburst ?

I was processing sentinel 1 sigma naught data, and I searched for the logic of debursting. Everywhere, I am getting the logic but not the exact mathematical formulation for deburst mosaic creation...

06 March 2023 4,221 0 View

Does an invited issue of a journal carry same impact as the original journal issue?

We usually receive many invitations of manuscript submission from different reputed journals. Recently I received a request from a reputed journal of Elsevier, but the website was not mentioned in...

19 February 2022 3,666 3 View

Can anyone please provide me a good reference of Bacterial culture filtrate LCMS study for identifying Bacterial endotoxin and exotoxins?

I need to know the specific column and HPLC conditions required to standardize the protocol.

13 July 2021 9,467 1 View

How to take into account additional modes while simulating circularly symmetric high impedance surface?

I am trying to design a circularly symmetric high impedance surface. However, when I run the simulation in HFSS to calculate the reflection phase, I see this warning message: "Port 1 supports an...

18 October 2020 985 0 View

How to two or more eigenmodes in HFSS simultaneously using eigenmode analysis?

I simulated a simple SIW cavity in HFSS eigenmode analysis to find out some modes. Is it possible to excite two modes simultaneously in HFSS using either eigenmode analysis or some other means?

12 October 2020 404 6 View

Is Foster's reactance theorem valid for two port networks?

The theorem states that the reactance of a passive, lossless two-terminal (one-port) network always strictly monotonically increases with frequency. Can this theorem be extended to two port...

03 December 2019 7,946 1 View

How nickel catalyst are prepared?

I want to prepare nickel catalyst ammonium bisulphite. Which is in liquid form. But problem is how nickel is used as catalysts. Whether i need to use nickel catalyst powder or by heating it and...

14 November 2019 3,143 3 View

How to do PLL for thyristor based 3 phase rectifier?

currently I am detecting zero cross for synchronization with 3 phase AC input which is not accurate.

12 February 2018 9,265 1 View

How many hours after the isolation of peritoneal macrophages can I treat with drugs?

After 2 hour for adesion, can I treat the cells with the drug?

19 August 2015 7,964 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

How to culture and maintain Lx-2 cells?

Hi there! I recently started working on Lx-2 cells. When I thaw the cells, they start attaching within few hours but later in about 2 days they started rounding and dying. I used DMEM+2% FBS...

31 July 2024 3,893 0 View

How to treat monolayer culture cell line with essential oil?

Hi all, may I ask you for advice about treating monolayer culture cell line with essential oil. Due to the hydrophobic character of the oil, I am concerning how can it equally affect to all the...

31 July 2024 5,301 2 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Why my negative control siRNA is decreasing the target gene's expression?

Hi Everyone, I'm using an siRNA kit to knock down a target gene. The kit guarantees that the negative control doesn't target any sequence in mouse genome, and when I use BLAST I don't find any...

23 July 2024 2,673 6 View